- Artificial Intelligence
- Infrared Distance
- Auto Positioner (Gait)
- Auto Release
- Continuous Servo
- Continuous Servo Movement Panel
- Horizontal Servo
- Kondo KRS ICS Servos
- Lewansoul Servo
- Lynxmotion Smart Servos
- PWM Servo Feedback (ADC)
- PWM Servo Feedback (I2c)
- Relative Servos
- Servo And Camera Server
- Servo Recorder
- Servo Summary
- SSC-32 Servo Controller
- UBTECH Alpha Servos UBT-12HC
- Vertical Servo
- Third Party Robots
- Touch Tablet
- Ultrasonic Distance
- Virtual Reality
Connect and control Robotis Dynamixel Servos to any EZB, including arduino and Robotis controllers. This open-source plugin converts the Virtual servo ports with any EZ-B (v0-v99) to control Robotis Dynamixel Servos. The servos supported are XL-320, AX-12, and XL430 models. Dynamixel Servos are very different than regular hobby PWM servos. Firstly, they are considered much more professional due to their design which is specific for the use in robotics. Each Dynamixel servo contains a microprocessor. The microprocessor is told what position to move the servo into over TTL at the configured baud rate.
EZB Cable Accessory
For Ezrobot or arduino users, this plugin requires a cable accessory to easily connect your servo to the EZ-B,
arduino or IoTiny. You can find the cable accessory in EZ-Robot's store by clicking here. If you desire to READ servo positions, the cable will need to be modified. There are instructions below for connecting the servo to READ positioning.
Wiring For Read Positioning
While we recommend using the Dynamixel servo Cable, you can optionally manually wire the servo yourself to any ezb controller using this diagram. If you wish to read servo data with bi-directional communication, you must connect TX and RX ports together. On the Ezrobot ezb, it’s port D5 and D6 (UART #1) together. On the EZ-B, D5 is TX and D6 is RX. This means if you connect D5 to D6, the EZ-B will be able to read the servo positions. You may also select UART 0.
There are three options for connecting the Dynamixel servos. The default option for controllers with hardware uart, such as the EZ-B v4 or Arduino Mega (not IoTiny) is UART 1 (port D5). The second option is UART #0 for the Robotis open cm 9.04 or open cr. The third option is low speed serial of any digital port for both arduino and IoTiny. To reference the pins of the EZ-B, consult the tutorial for the EZ-B by clicking here.
*Note: we highly recommend using Hardware UART on the EZ-B v4, open cr, open cm 9.04, Arduino Mega, or any controller with hardware UART only. Do not use software UART on these controllers. Only use software UART when using a controller that does not support hardware uart, such as Arduino Uno or oTiny. Also, a controller with a hardware UART is necessary when reading servo positions. Read Electrical Wiring further down in this document for bi-directional communication with EZ-B v4 for reading servo positions.
Most Dynamixel servo documentation states the operating voltage in the manual. Check the documentation for your dynamixel servo model to ensure your power source is sufficient. If you experience unusual behavior of Dynamixel servos, the first common issue is insufficient power.
The Dynamixel Servos each have a unique ID. Because they are chained together through one cable, each servo must be given a unique ID. Servos with the same ID will respond to the same commands, and therefore mirror their behaviour. New Dynamixel Servos come pre-configured with the ID of 01. servo V0 relates to dynamixel ID:0, V1 is dynamixel ID:1, v2 is dynamixel ID:2, and so on...
Using this configuration utility, you can assign new ID's to servos. You may also test the servo to ensure the ID was successful.
The LEDs on the dynamixel servo can be controlled using the EZ-Script ControlCommand(). View the Cheat Sheet when editing a script to see the available ControlCommand syntax for the Dynamixel Plugin.
There are a number of EZ-Script commands added with this control. The commands are as follows...
Returns the temp of the specified servo
Returns the direction of load on the specified servo
Returns the load of the specified servo
Returns a ping response if the servo exists. Otherwise, returns false
Step by Step Instructions
Once you have the servo wired, and sufficient power is provided, you can use any control in EZ-Builder that uses servos. This means it will work with Auto Position, Camera, WiiMote, Joystick, and more. In this example, we'll show you how to move a dynamixel servo with a generic servo control. Before following these steps, ensure you have this plugin installed.
Connect to your EZ-B v4 or IoTiny controller
Add the control by selecting the Project tab and Add Control
Navigate to the servo tab and select Dynamixel. If the plugin has been successfully installed, you will see the Dynamixel plugin in the list.
The Dyamixel control will be added to your project. Press the Config gear icon to load the configuration screen.
Enter the baudrate that matches your servo configuration. The servos have a baud rate that can be specified, or a default baudrate shipped from factory. If you need to change the baudrate of the servo, use the Dyanmixel utility. You cannot change the baudrate of the servo in ez-builder. This value is the baud rate that the EZ-B will use to communicate with the dynamixel servo. This must match the baudrate of the servo.
Specify what port the servo is connected to on the controller. It is important to follow this recommendation. There are blue question boxes in the plugin (and throughout the EZ-Builder software) to assist you robot development. It is recommended to use the blue question marks and read the content to understand what options do.
Each dynamixel servo will have a unique ID. Enable each ID for the servos by checking the respective box. When an ID is checked, the EZ-Builder software will use the Vx (virtual servos) corresponding with that ID. For example, if you enable Dynamixel servo ID #2, the EZ-Builder V2 servo will control it. Also, specify the protocol version of the servo. Different dynamixel models will use one of the two protocols. Consult the datasheet of the dynamixel servo to know what protocol it uses -or- contact Robotis for more information on using their product. To get full resolution of the servo, also ensure you have entered the MAX resolution for that servo model. Each model has different resolutions, or it can be configured using the Dyanmixel utilities.
After you have enabled your servos, press Save
Now we will show you an example of how the servo can be moved. We will do this by using a generic horizontal servo control. Press Project -> Add Control to return to the add control menu. Navigate to servo and select Horizontal Servo. Remember, any control in EZ-Builder that uses servos can now control dynamixel servos by the respective Vx (virtual) servo ID.
Press the GEAR icon to configure the horizontal servo control.
To configure this control to use a virtual servo, select the servo to bring up the port dialog. This applies to all controls in EZ-Builder that use servos.
Select the Virtual servo ID for your dynamixel servo from the list and press Close.
Now use the sliders to specify the Min and Max position that you wish this servo to move and press Close.
You can now control the dynamixel servo with the horizontal servo control. To find out more about servos, consult the learn section of this website for activities on using your ez-robot product.