EZ-Robot EZ-B IoTiny

EZ-Robot EZ-B IoTiny

Connection Type
Wi-Fi / USB
Number of servos
Audio Support
Camera Support
Available for purchase from:

Connect Something!

Introducing IoTiny, the smallest tiniest Robot/IoT controller of the EZ-B family. Powered by a 100mhz Cortex M4 ARM processor, the form factor gives you the ability to use custom enclosures or fit in the tiniest of places. Invent new IoT projects by easily controlling and automating nearly anything over the internet.


Firmware code, hardware design files and documentation are all available on GitHub.

Compatible with EZ-B v4!

The IoTiny is a tiny EZ-B v4. The IoTiny operates the same as an EZ-B v4, which means the tutorials, software and examples apply to both products. Enjoy the power of EZ-Builder with the IoTiny, because it is compatible with the EZ-B v4 features. Just, a little bit... tinier!

Includes Many Starter Projects (view)

  • RGB Animations
  • Camera Vision Color Detection
  • Movement Tracking of Color with Camera
  • Mobile App Creation
  • MYO Gesture Armband Control
  • Nest Thermostat Integration
  • and more!


  • Controlled by EZ-Builder PC and EZ-Builder Mobile
  • Wi-Fi (Control, Telnet, HTTP, Discovery)
  • Supports EZ-Builder's controls, such as Speech & Visual recognition
  • SDK, Mobile & Microsoft Windows Software
  • Verbal Setup Prompts
  • 8 x Digital I/O, Servo, UART (tx only)
  • 2 x ADC
  • 1 x i2c
  • 1 x Camera Video
  • 1 x Speaker Output
  • Hundreds of controls & 3rd Party Plugins

IoTiny ports

Simplicity and power.

The EZ-B IoTiny can be controlled over WiFi using the graphical ez-builder software on your PC or mobile device, without needing to program. The less time you need to spend with compilers, hardware programmers, and debuggers, the more time you can spend building and designing robotic projects!

The v4/2 is the next generation brain of your robot or IoT device, powering over 20,000 robots worldwide! Give your custom robot or IoT project features inspired from science fiction! With the electronics protected by a stylish plastic shell, the ez-bv4 clips into your ezrobot Revolution chassis or custom robot. It is easily controlled over Wi-Fi using ez-builder software.

The ez-bv4/2 boasts two Cortex ARM processors running at 220MHz to provide servo, digital i/o, real-time audio/video streaming and more! 5 volt tolerant I/O, energy efficient digital switching power supply, Wi-Fi connectivity with security, embedded web server, telnet server, amplified digital audio with speaker, 3 I²C ports, 3 x UARTs, 24 multi-use servo/digital/serial ports, 73 servos (Dynamixel & PWM), 8 analog ports, and integrated video, all in a tiny 2.1" x 2.2" size!

3 PIN (GVS) Connectors

Each port has 3 pins, which are GND (Ground), VCC and Signal. The GND and VCC are for powering the device connected to the port. The Signal pin is connected to the EZ-B Microchip for reading or writing data from Digital or ADC. The GND and VCC pins are not connected to the Microchip, they are used only for powering the peripheral connected to the IoTiny.

For example, a servo has a 3 wire plug that connects to one of the EZ-B Digital Ports. The wires of a servo connector are GND, VCC and Signal. The GND and VCC provide power to the servo's motor and circuit. The Signal wire carries the information to tell the servo what position to move.

Connecting Camera

The EZ-Robot Camera connects to the EZ-B IoTiny the same way as an EZ-B v4 with a 6 pin cable. Notches on the male connector match the EZ-B's female connector. This prevents the plug from connecting incorrectly. The camera connection is unique, making it easy to identify where to connect. It is impossible to connect the camera cable to the wrong connector, as it only fits in the matching plug.

Connecting Servos & I/O

The servos connect in the same fashion to the IoTiny as the EZ-B v4, shown in the video. Much like your home theater speakers, the cables of the EZ-B and peripherals are color coded. The BLACK cable on the peripheral (i.e. servo) will connect to match the BLACK side of the EZ-B connector.

Making an IoT Product

Learn how to create an Internet of Things (IoT) product using IoTiny.

Unregulated Power I/O

As a IoTiny, it is important that you know how the power pins work. This is because you will be building a custom robot with custom power requirements. The IoTiny does not regulate the power on the I/O pins. This means that if you provide 12v to the IoTiny, the I/O pins will output 12v. Of course, this will damage any +5v peripherals that you connect to the IoTiny when using 12v. You must be aware of how much power is being provided to the IoTiny and what you are connecting to the I/O pins. For example, the EZ-Robot Servos do not like power above 7.4 volts - which is why we recommend using Rechargeable AA batteries in the provided holder. If you are wishing to use an alternate power source, please be aware of this message and select a voltage rating that works with your application.

*Note: The only ports that have regulated power are for the Camera & i2c.

Learn Your Port Types


Working with digital means True (On) or False (Off). True means any voltage above 1 volt, and False means GND. There are 8 digital ports on the IoTiny (D0 to D7)

Output is writing to a port: When a port has its digital value set to True, then a +3.3 voltage will be outputted on that port. If the port has its digital value set to False, then the port will be GND.

Input, is reading from a port: You can read the value of a specific port. This is how you can check for voltage, On or Off. Any voltage above GND (and below +5 volts) will be returned as True, a short to GND will be returned as False.

Example peripherals for digital ports are Switches, Servos, Ultrasonic Distant Sensors and Buttons.


ADC is short for Analog Digital Converter, and is read only (input only). This method reads voltages into the EZ-B Robot Controller. There are 2 analog input port on the IoTiny (A0 to A1).

Reading Relative Voltage: The returned value will be between 0-255 in 8 bit mode and 0-4095 in 12 bit mode. These values represent the input voltage on the specified port. The value will be relative to the input voltage that will between 0 and 5 volts. Example in 8 bit mode: Value 0 = 0 Volts, Value 127 = 2.5 Volts, Value 255 = 5 Volts.

Reading Absolute Voltage: Returns the value in actual volts on the specified port.

Example peripherals for analog input are Sharp GP2 Analog Distance Sensors, Pressure Sensors, Light Sensors, Sound Sensors, Color Sensors and reading voltages.

Serial (tx only)

Every digital port of the IoTiny can transmit serial data. Serial Communication is the process of sending data one bit at a time in a sequence. Serial communication is common with many peripherals because it allows commands to be transmitted over one wire. The transmission works similar to Morse code.

The Sender and Receiver need to be configured for the baud rate (speed) in which the data will be transmitted. Common baud rate speeds are 300bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200.

Example peripherals for serial communication are LCD Screens, Motor Controllers, Servo Controllers, Computer Communication, Arduino Communication, iRobot Roomba and more.


The I2C is also referred to as the "Two Wire Interface". There is an I2C connectors on the IoTiny. I2C is a communication method invented by Philips that is used to communicate with peripherals. The I2C uses two wires for communication, Serial Data Line (SDL) and Serial Clock Line (SCL).

I2C devices can be chained together in a network formation. Each device is given a unique address. The IoTiny has one I2C header which provides both signal wires and +3.3v power.

Example peripherals for I2C communication are LCD Screens, I2C enabled Servos, BlinkM Multicolor LEDs, and more.

Click here for more information on understanding i2c addressing.

Related Content

Create Auto Position Actions From EZ-Script

Create Auto Position Actions From EZ-Script

This tutorial uses the ControlCommand() EZ-Script command that instructs the Auto Position control to create a frame and...
Error Dowload Ez-Builder

Error Dowload Ez-Builder

I encountered an error downloading ezbuilder: Ez-builder could not be installed on the following windows versions:...
live hack
Thomas The Train Live Hack....The Better Version Of His Former Self!

Thomas The Train Live Hack....The Better Version Of His...

I had this idea a while back of using the classic wooden train tracks that everyone seems to have hiding in their...
Firmware Iotiny

Firmware Iotiny

My IoTiny has corrupted the Firmware and now it no longer works with just a blinking blue Led and does not recognize on...
2 Iotinys With Camera Power Needs

2 Iotinys With Camera Power Needs

I built a D-O droid and has a Iotiny to run 6 servos and a speaker, once the sounds are known. It has a very thin head...
live hack
Rock Em' Sock Em' Robots Live Hack...Back Once Again With The Ill Behavior!

Rock Em' Sock Em' Robots Live Hack...Back Once Again With...

Rock em' Sock em' Robots Live Hack (Part 3) I've always loved the look of the Rock'em Sock'em Robots game but absolutely...
Artificial Conscience

Artificial Conscience

I’m not sure if we’ll be able to solve this question but if anyone could get close I feel it’d be you guys here in the...

Is The Use Of Lidar Possible?

I am designing a mini robot system using ez robot parts. Before I actually buy a kit I wondered if it is possible to add lidar to the systems?

Movement Panel For Robosapien

Hi, I a a nubie with Synthiam and have done much research and searching.  When I first run EZ-Builder it gives me several demo robots to load, one of...
live hack
Rock Em' Sock Em' Robots Live Hack....The Heat Is On!

Rock Em' Sock Em' Robots Live Hack....The Heat Is On!

Rock em' Sock em' Robots Live Hack (Part 13) ***Now Happening at 8pm MDT****** Lucky number 13 the day after Halloween!...
Amplifying Audio From A Iotiny

Amplifying Audio From A Iotiny

Im using the soundboard exb to play audio files but they are very faint.  Is there a way to add an amplifier like on the...
live hack
Rock 'Em Sock 'Em Robots Live Hack....A Million Punches!

Rock 'Em Sock 'Em Robots Live Hack....A Million Punches!

Rock em' Sock em' Robots Live Hack (Part 14) ***Sorry, I'll be away this weekend so I am doing the Live Hack on a...
Who's On Thingiverse?

Who's On Thingiverse?

I know a lot of you guys are quite active in the 3D printing community. Are you on Thingiverse? If so, what's your...

Soundboard Control

I am wanting to play audio files via the EZ Builder Mobile App on my Tablet - not PC and not through the iOTiny. There doesn't seem to be any way of...

New EZ-Builder Has No Longer Config Icon Soundservo??

Downloaded the new EZ-Builder and now there is no longer a config icon on the soundservo plugin. Anyone the same problem?

Everytime I Got A Error With My Mobile Interface.

Everytime i got a error with My Mobile Interface when updating installed apps. Photo.