All Community Content
Synthiam Credit
Log In
Earn Free Credit
Share your robots, answer questions, and help others — earn credit toward ARC Pro, AI credits, and robot swag.
Exosphere
What is Exosphere?
Drive Real Robots, Anywhere
Remotely operate robots around the world or add live telepresence to your own build — straight from your browser.
Discover Exosphere
Synthiam Swag
See All Swag
I Make Robots Crew Socks
Recent Robot Skills
View All
Feetech Serial Bus S…
Control Feetech SC serial bus smart servos via EZB UART or PC COM port with ARC virtual ports,...
Feetech RS485 Servo
Control Feetech serial bus smart servos via EZB UART or PC COM port in ARC using virtual ports...
Total Speech Recogni…
Offline Windows speech recognition with open dictionary, confidence filtering, and scriptable phrase...
Featured
4-series bar chart for real-time sensor comparison in ARC; set titles, values, RGB bar colors and conditional coloring via EZ-Script.
Featured
Centurion security robot inspired by Cylons, Terminator and Person of Interest, built with Synthiam ARC for mission-focused control and creative...
blog
Ez-Robot At Calgary Comic Expo
EZ-Robot at Calgary Comic Expo April 27-29: live robot builds, flying robots, AR demos and unveiling of the Complete Robot Kit.
15
7 k
Lumpy |
release
Release 2012.05.06.00
Enable Sabertooth motor control via one-wire serial movement panel, GPS data view, and resizable EZ-Script editor for EZ-Robot
11
5 k
Bookmaker |
question
Sdk Documentation Discrepancies
DJ, There are a few incorrectly documented values in the SDK. 1: The comment for SERVO_SPEED_SLOWEST indicates the value should be 255 when it is actually 10. 2: The comment for SERVO_CENTER says 70 when it is actually 50 3: The comment for SERVO_MAX says 140 when it is actually 100 Thank you.
1
2 k
ww321q |
question
Omnibot + OQO + EZ-B
I wanted to share the start to my Omnibot build. Turns out the OQO-02 covers the tape deck and clock hole nicely with just a bit of dremel plastic melting. Picture Now imagine it...
24
7 k
bret.tallent |
question
Ezb Firmware Update Failure Help
ok all was working fine with ARC until i decided to upgrade to 12 26 version. down loaded ok then tried to run firmware update program. failure program...
26
5 k
mitchmen14 |
question
Question For Lloyd
Hey I wanted to send you some free dynamat sound deadening material for gizmo and some fans , I know you posted a email or something for me to contact you and I wasn't on the site for a couple days , I was in the hospital ( nothing too serious kidney stone and a restriction). If you would like to email me today Lloyd at [email protected] I would...
5
3 k
jstarne1 |
question
2.5 Amp Motor Controller.... Help!
I wired up the controller per DJ's instructions. It's getting power. The little light is on but nothing happens. Any ideas? Troubleshooting techniques?
36
6 k
kkeast |
robot
Jamerperson's BRAD (My First EZB Robot)
Voice-activated rolling robot, ezb-powered: mic, random-note speaker, ping collision sensor, moving arms/torso, head LED, sealed power...
18
7 k
MovieMaker |
question
The Function Switchvideochannel() Or Videochannel() Not Working.
hey, in the ar-dron tutorial the function SwitchVideoChannel() and VideoChannel() not working. do you know why? and if theree is any way that we can change it to the vertical camera? thank shiran
0
2 k
shiran |
question
Software Question (.Net, Com, Sdk Etc.)
I am using the ez_b SDK with matlab, and trying several methods. Here are a couple questions based on my attempts: Q1) I used the the windows SDK gacutil to load the ez_b.dll into the .net Global Assembly Cache (GAC), which it did. But when I tried to load the ez_b assembly I got this message: "Could not load file or assembly 'EZ_B,...
9
3 k
riledo |
question
Hello! (A Short Introduction)
Hello everyone! Just thought I'd introduce myself real quick My name is Henrik, and I'm from Sweden. I bought my EZ-B back in 2011, but haven't been active here at the forum, so I thought I'd change that! When I'm not playing around with my EZ-B I'm a programmer/systems developer/webdesigner for a small company here in Sweden. I've always been...
9
3 k
incols |
question
Is Instructables.Com Legit
I understand how big the site is (thousands of threads and members) but if you (a member) win a prize in one of the competitions, would it be safe to release personal information to redeem it. (address, phone number, etc..) i am not questioning the website, just curious p.s. Found EZ-B on there
3
2 k
wallekid1 |