Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Rplidar
Slamtec Lidar driver for ARC; scans 360° and publishes distance data to NMS for mapping, obstacle...
Kinect Xbox 360 Dept…
Converts Xbox 360 Kinect depth frames into NMS obstacle scans for ARC path planning, SLAM, and...
Featured
Run custom scripts when speech starts/ends to sync servos and LEDs to spoken $SpeechTxt, with loop support, stop button and logs.
Featured
Betty9: a 6' tall fembot with servos, blue eye LEDs, Arduinos, EZ-B and Echo Dot, mounted to a hacked Segway MiniLite for guided locomotion.
question
Ping Ping Ping
Question for you guys..anyone. Other than object avoidance, is there anything else a ping is good for in association with EZB?
43
8 k
Dunning-Kruger |
question
Software Item Request
A couple of us have been tossing around the idea of some sort of speed ramp. Speaking for myself, I'd like to have one for servo. Now I think this would have to be done in auto position, only for the fact that you would need some form of time reference. Say something like speed 20 to 15 over 3 seconds then speed 15 to 8 over 5 seconds, then full on...
4
3 k
Troy |
question
Does Anyone Of The Lucky Ones Want To Sell A V4
I do not want to wait until July for a v4, does anyone want to sell one, when they get it? I have a v3 and money.
7
2 k
Dave Schulpius |
question
Ar-Drone V.1 Navdata
Hi, i am trying to get the navdata out of the AR drone while tracking an object. i was able to retrieve th object position using the following script $filenamex = "c:\logx.txt" %create log for x coordinates% $filenamey = "c:\logy.txt" %create log for y coordinates% :START %retreive centroide position% IF ($CameraIsTracking =...
1
2 k
DJ Sures |
question
Ping_Wait
Is "Ping_Wait" command pause the script until the distance match the specified value?
4
3 k
Rich |
question
Volts For Signal
the signal ports on the ez-b4 ,does that give volt?.when i see the tutorial from the leds, i see they are connected to gnd and to signal ports. blush
19
4 k
Nomad 6R |
question
Dj Sures.Ez-Bits Need More Documentation!
I would like to see in one place a bill of materials for all the items required to be printed for JD, Rolli and 6. That way, I can queue...
2
3 k
Jason |
question
Connect To Ar Drone From Script?
Hello EZ-robot people! I was searching the web for an ARC script command, that will enable me to connect to the AR Drone from within a script, but could not find how to do it. Any ideas? Thanks.
6
2 k
Rich |
question
Ez-Robot Revolution In Complex Magazine!
I finally found the new April/May issue of Marc Ecko's Complex Magazine which features a full page of EZ-Robot goodness! Check it out:
3
3 k
jstarne1 |
question
Omnibot 5402 Head Movement
Hey guys. Ive been slowly working on one of these and I have come to a bit of a stand still. Im looking for the best way to get his head to move left and right without being to complex. So far ive seen maybe 3 different ways it was done. The only problem is 2 are only seen briefly in DJs omnibot v2 and v3 videos. While the 3rd is just more worl...
2
3 k
Xuven |
question
Mp3 Module
Has Anyone worked with or used www.ebay.com/itm/301094708500?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT Was wondering if it was the same as www.mdfly.com/index.php?main_page=product_info&cPath=&products_id=284
3
3 k
Xuven |
question
Reload Firmware To Controller
I think I may have a corrupted os on my controller. After the last upgrade it seems that there is a delay of about a second or two and pwm controls are not acting right. The reason that I believe that I may have a corrupted os is that I may have been too far away when I did the update. I tried to reload but it says that it is already the current...
11
4 k
Purple |