Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Inverse Kinematic Ar…
Control robot arms with inverse and forward kinematics, converting X/Y/Z positions into joint motion...
PCA9685 Servo Driver
Convert an EZB I2C bus into a 16-channel PCA9685 servo controller, exposing V0..V15 with...
Rplidar
Slamtec 360° LiDAR driver: calibrated, offset/rotation-adjusted scans published to ARC NMS for...
Featured
Control Feetech serial-bus servos via EZB UART or PC COM, mapping servo IDs to ARC virtual ports; supports position, speed, release, acceleration.
Featured
Wall‑E replica using EZ‑B v3 controller: wheel/arm/head servos, BlinkM eye, 2.4GHz camera, SparkFun MP3 trigger, 6V 3000mAh NiMH battery, PING...
question
The Robot Program
how do i check the robot program as read or seen the video's.
9
3 k
Nomad 6R |
question
Accidental Short To Ezb4 At Sonar Ports
I was adding a second new ultrasonic sensor and forgot to turn off main battery switch, a power wire accidentally touched a wire I was adding to the EZB4 front D21 D22 area for sonar connections and there was a spark but the main EZB fuse did not blow and it still powers up but no more audio on the start up voice and the Wi/Fi is still connecting...
5
2 k
Dave Schulpius |
question
Ssc-32U Servo Controller
Hey Everyone, I am currently trying to figure out how I will connect this servo controller to the Ezb V4; I am stuck on which cable to use as well. I also wondering about...
4
3 k
PhG |
question
Hdd Servos
Is there a US authorized retailer that sells the new HDD servos.
20
4 k
Toyhackrobotic… |
question
Camera Lights
I have an ezb camera and tested it before putting it into my robot eyes, when I connect after installing it, the lights goes red, green blue then no lights at all. When I tested it before it went green and I could see images. Does the ezb camera have a reset button on it some where? Thanks for anyone's help.
6
2 k
Redzone |
question
Multiple Ez-Robot Microprocesssors
Couldn't find answer to this question. I know I can have more than 1 micro-controller on a Robot. How do I install it and how do I operate them both at one time.
2
3 k
Ellis |
question
Multiple Blinkm
I am not understanding how to change colors via scripting if I have 2 blinkm connected. This will fade to blue I2CWrite(0,0x09,"c",0x00,0x00,0xff) How do I make the other one fade to another color? I cant figure out how to address the each blinkm individually. Thanks.
4
2 k
CochranRobotic… |
question
Darth Jader Software
is there comming a darth jader for download? and the helmet for 3d printing.
11
3 k
Nomad 6R |
question
Robot Only Turns One Way
Afternoon All. I am using Ultrasonic radar which scans and displays reds dots ok. Also 4 wire H bridge which operates in all directions ok. But when used together the Bot...
5
2 k
Toyhackrobotic… |
question
Long Range Xbee & Other Robot Communication
I was browsing the EZ forum and saw some one mention the incredible distances that you can communicate with robot,RC vehicles,balloons...
6
3 k
robo rad |
question
Google Home Diy With Raspberrypi
FIY The MagPI magazine #57 contains a DIY project for a Google Home in a Box: https://www.raspberrypi.org/magpi/find-the-magpi-57/ Copies have been shipped...
0
3 k
ptp |
question
Auto Position Thread Error
As soon as I connect SIX I get the following error. If it's being caused by a frame how do I tell which one? I can open the servo configuration and the servos alll move fine. 4/6/2017 12:01:09 PM - Auto Position Thread Error: System.IndexOutOfRangeException: Index was outside the bounds of the array. at EZ_B.AutoPosition.MoveImmediate(String...
6
2 k
jmp23834 |