Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Inverse Kinematic Ar…
Control robot arms by X,Y,Z(cm); computes joint angles (inverse kinematics), shows forward...
PCA9685 Servo Driver
Convert an EZB I2C bus into a 16-channel PCA9685 servo controller, exposing V0..V15 with...
Rplidar
Slamtec 360° LiDAR driver: calibrated, offset/rotation-adjusted scans published to ARC NMS for...
Featured
Real-time servo position input via Arduino ADC over I2C; supports Nano (6 channels) or Mega (16), configurable I2C address and scalable chaining.
Featured
Control EZ-Robots using Oculus Rift and brainwave interfaces-explore hacking, integration methods, and control options.
question
Omnibot 2000 Tray Needed
Does anyone have a tray for an OMNIBOT 2000 they would sell? I just picked up an OMNIBOT and would like to complete it. Thanks!
5
2 k
omnird |
question
Can A Separate Microphone Be Connected To An Ez-B V4
Can a microphone (not speaker) be connected directly to an EZ-B V4 ? I am building an R2D2 and would like to allow...
8
3 k
Perry_S |
question
Latte Panda Built In Io
Hey guys, looking for Latte Panda owners out here. I know there are some input outputs on the board and I was wondering if anyone knew of a simple way to utilize them in...
9
3 k
Andy Roid |
question
Overlay Not Working On Mobile App
Overlay not working on mobile app. Is it even possible to run on mobile? Also unable to get tracking to work on mobile.
4
2 k
Chelsea |
question
Servo Holding Brake
Might be biting off more then I can chew, but going to try and design a servo holding brake. Initial plan is the try and keep it 15mm thick by 25mm in dia. When not powered will hold...
22
11 k
rz90208 |
question
Ez-Chatbot. (An Idea)
@DJ and EZ-Robot team. Hi guys. While I have been setting up audio scripts, soundboards and the Pandorabot control, I had a thought for a possible added feature/control for ARC...
15
7 k
TMesserschmidt |
question
Ez-B V3 Wanted
Hi All, I am looking to buy an EZ-B v3 and perhaps a camera and other sensors (i.e. ultrasonic) that would work with it. I am running an older version of the software and cannot use the v4. board. Does anyone have one they are willing to sell? Thanks, Jeff EZ-B v3
10
3 k
jphillipsnj |
question
Snybot Plugin Question
I tried loading the SynBot plugin following the tutorial and the plugin just comes up as a white box. I tried loading it into a clean new project and got the same results. I am...
27
6 k
Jlucben |
question
Errors When Trying To Save To Ez-Robot
Anyone else getting this error when trying to save to the EZ-Cloud App Store ? This just started to happening. I have been able to save in the...
16
3 k
DJ Sures |
question
How To Connect Ezb To A Create 2
I have been looking on the forum for a wiring tutorial for the ezb and create 2. There are a lot of ideas and very complicated ideas that seem to work but...
131
16 k
faengelm |
question
Ez-B Questions For Johnny Five Robot Build
Here is a YouTube video with my VERY novice questions. Thank you, Terry.
16
3 k
J5GURU |
question
Qr Codes And General Reliability
Hi guys, just seeming some feedback from those fairly experienced with the EZ's. I have been using a JD on a display booth at a future cities summit with my...
2
2 k
alydun |