Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Rplidar
Slamtec Lidar driver for ARC; scans 360° and publishes distance data to NMS for mapping, obstacle...
Kinect Xbox 360 Dept…
Converts Xbox 360 Kinect depth frames into NMS obstacle scans for ARC path planning, SLAM, and...
Featured
Add Google DialogFlow NLP to ARC: conversational intents, parameter prompts, scripted responses, service-account setup and programmatic robot...
Featured
Custom 'Losing Louie' diorama and handcrafted drones inspired by Silent Running-stunning detail by Destiny Models with custom electronics and FX.
question
Jd Eyes And Rgb Led Array Ez-Bit Sneak Peek
There's been questions about how JD's eyes work - and the 18 RGB LED Block EZ-Bit. Well, I shot this quick video to demonstrate how...
9
4 k
Jeremie |
question
Got A New Computer
Well I finely got a computer it has win 7 but it only realy good for my robot there is a lot I cant get it to do like will NOT read any of my disks at all and when I plug it into the net it will not see any of my usb drives but it will work for my bots so im now back to playing with my toys oops I mean Robots:D:D and photos loog great on it
7
3 k
Wolfie |
question
2 Unrelated Questions.
First I have torxis/invenscience 12vdc servos. They are powered via 12vdc and at full load draw approximately 5 amps. So first question is how much current can the new ezb4 put...
22
6 k
Dave Schulpius |
question
Still On Ez-B And Bci
My first project with the EZ-Robot involves using the Developer Kit to create something that will be controlled through Brain Computing Interface with an Emotive Epoc headset. Possible? Any awesome BCI + EZ-Robot ideas?
2
2 k
nastrange |
question
5V Inline Regulators For Sensors And?
I know sensors like pings and IR will need a 5V regulator inline if you put more than 5V through the V4 board... Just noticed my sabertooth motor controller also uses a 5V input line in addition to the signal line and ground line... Does this mean even motor controllers will need a 5V inline reg as well? I tried removing the +5V wire from the...
24
6 k
Rich |
question
2.5 Amp Motor Controller
Does the same procedure apply to connect the 2.5 amp motor controller to the v4 compared to the v3 2.5 amp motor controller
9
3 k
Jeremie |
question
Windows Surface
Hi can the windows surface download ez-biulder confused
9
3 k
Rich |
question
E-Z Builder Interface
Hi, What happened to the interface? Using Win 7 here with multiple monitors. Last couple of versions unable keep controls in same place after saving and reloading. Unable to use...
6
3 k
Dunning-Kruger |
question
Can't Update My Avatar
@Chrissi... (I think you deal with the web site)... Can't seem to update my avatar under my user settings... I can change other settings but for some reason I can't upload a...
10
4 k
Dunning-Kruger |
question
Where's The Comm Port Procedure For The Ezb4 ?
Can't find the post detailing the WiFi steps for the EZB4 ports to establish a connection.
29
6 k
mdeming1 |
question
Wheel Spec Clarification Needed
Hi all I'm happy to say I finally finished my robot chassis such as it is this weekend. When I make a more square version I'm going to use the suggestions...
9
9 k
mdeming1 |
question
Mr. Clock Radio On Ebay
I was looking on ebay and I found a Mr. Clock Radio for sale. It has a Buy it Now price of $34.99 US dollars. Free shipping to the lower 48 in the US, and International...
0
4 k
joseph4760 |