All Community Content
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Rplidar
Slamtec Lidar driver for ARC; scans 360° and publishes distance data to NMS for mapping, obstacle...
Kinect Xbox 360 Dept…
Converts Xbox 360 Kinect depth frames into NMS obstacle scans for ARC path planning, SLAM, and...
Featured
Control Roomba/Create via ARC: drive, stream sensors, read encoders, configure COM/HW UART, and send pose to NMS for mapping/navigation.
Featured
Cookie Monster robot showcases EZ-B voice recognition and speech synthesis with dynamic phrase-triggered commands and rapid prototyping
question
Until The Neopixel Bits Become
Until the NeoPixel Bits become available... https://www.ez-robot.com/Shop/AccessoriesDetails.aspx?prevCat=9&productNumber=54 ...what is the preferred...
6
2 k
DJ Sures |
question
Hello,I Am New To JD And I Wan
Hello,i am new to JD and i wanna print one part of it.how do i connect my 3D printer and laptop?Any help will be much appreciated.thank you.
1
973
DJ Sures |
release
ARC Raspberry Pi 2019.02.14.00
Synthiam ARC Valentine's update speeds visual control rendering, faster add, auto-arrange, project load and debug popup
0
3 k
question
Is It Possible To Convert Bloc
is it possible to convert Blockly to EZ-script? I have a good routine I want to use that I created in Blockly, but it needs a few tweeks that I need to add in EZ-Script.
2
2 k
edbot |
question
New Here And Am Asking Some Qu
New here and am asking some questions. My project is an independent drive via 24 volt Jazzy motors controlled with a Sabertooth 2x32. My wish is to have autonomous operation and have RC over ride. I have an operational RC and operational Arduino autonomous but have not been able to assemble both. Dimension Engineering (Sabertooth) have guided me...
5
2 k
DJ Sures |
question
So I Am About To Buy Another L
So I am about to buy another lipo battery for the EZ VB4, the one I was using for my EZ BV4 was a 7.4V, 1300mAh and I was wondering if it is safe to use a 11.1V, 1300mAh. I have read a few threads in this community but I just felt safer in asking if someone has used the 11.1V and has not had any issues burning anything.
3
2 k
Heattroks |
question
HDD Servos
Hi, I am 3d printing the STLs for the Revolution6. I have 12 HDD servos on order, due in March. In the meantime I have to hand the Developer Kit which has HD servos. These do not seem to fit the EZ...
4
2 k
itsmeintorre |
question
Hi, Pretty New To This And Sea
Hi, pretty new to this and searched but couldn't find a answer. I have about 10 servos that run on 5v and I want my ez-b v4 to run them, is the pwm from the v4 ok as long as you power from a 5v source? Thanks!
4
2 k
Almostrodney |
question
Hello Everyone,We Have 4 EZ-
Hello everyone, We have 4 EZ-Robot Humanoid JD. The 4 ez-robots are 2 years old. We tried connecting via phone and it worked but the capabilities of the phone software was limited. the PCs we used and had the software recently downloaded wouldn't recognize the robot at all. But one of the teammates who had the software downloaded from the first of...
3
2 k
DJ Sures |
robot
Jstarne1's Ryobi 40V Robot Mower With 40V Trimmer Whiskers By Jstarne1/ Starnes
Back to building robots after moving to Chattanooga and...
167
31 k
Nomad 6R |
question
Hello Community,I Would Li
Hello Community, I would like to deploy something similar to this project NeoPixel Ring with Arduino as control board but I need to use LED strips. 60 LED qty. Will this work for LED strips? Or is there a simpler way to control many LEDs with the EX-B Help is greatly appreciated. Thanks, Mark
1
2 k
Jeremie |
question
We've All Seen It. The Super
We've all seen it. The Super Armatron has it, the Omnibot 2000 has it, and if you take away the head of Gypsy from MST3K, it's all you have left! I am of course talking about those fun bits of rubber tubing that add a clean, industrial flourish to any robot. I'm in the process of taking an old Robie Sr. and giving it the same treatment that DJ...
2
2 k
Bobsheaux |