Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Rplidar
Slamtec Lidar driver for ARC; scans 360° and publishes distance data to NMS for mapping, obstacle...
Kinect Xbox 360 Dept…
Converts Xbox 360 Kinect depth frames into NMS obstacle scans for ARC path planning, SLAM, and...
Featured
Control robot servos with Microsoft Xbox 360 Kinect body tracking; map joints to upper/lower body servos with smoothing and pause control.
Featured
Autonomous 1m hexapod with EZ-B V4-2, 18 servos, LiPo power and Synthiam Blockly control for garden navigation, recharging and sheltering
question
Question With Release() Command
Greeting all, It has been a long while since I posted here. I have been working on my Inmoov whenever I can find time, which is not a lot, but slowly, very...
28
7 k
MovieMaker |
question
Robonova Servo
Hi. I have planned to use ez-b4 for my robonova-1. It uses Hitec HSR-8498HB servos. Normal servos turning 0-190 by 1-2ms signal These servos turning 0-190 by 0.55-2.45ms signal. So It turns by...
8
3 k
thetechguru |
question
Ezb To Control Adruino
Anyone have any idea if it's possible to fire an Adruino routine using just 1 digital signal pin of the EZB. I have a Arduino doing a simple little servo routine with 10 small servos, and don't what to waste 10 output pins of my EZB. Looking for the output of the EZB to signal the Arduino to start, just like pushing the reset button on it. I could...
5
2 k
thetechguru |
question
Builder Won't Open
My son and I made our first bit of progress last night by getting our little bot up and going. But when we opened builder this morning, we noticed the "update available" tab flashing so we clicked on it. it took us to the download page which we did and everything went normally until we clicked on "finish" to exit the installer....
31
5 k
sv.jgalloway |
question
Goto Last Loop Variable Goto + Variable Goto($Variable)
Has anyone figured out way to get the goto() function to work with variable so it can goto the last defined...
42
7 k
Dave Schulpius |
question
Cybot And Running Multiple Scripts
Cy_MainTest1.EZB Hopefully,the file uploaded ,my first time. Looking for a little help. Since I am still learning much about Ezb script writing, I have...
4
3 k
RoboHappy |
question
Ezb-V4 Power
For a Roomba application, will the EZB V4 handle the unregulated power input in the same way the EZB V3 could? I saw one discussion where the EZB V4 smoked after trying this....... https://synthiam.com/Tutorials/UserTutorials/115/1
3
3 k
MarkTheBotBldr |
question
Using And H-Bridge 2.5 Amp Motor Controller To Control Stepper Motors?
Ok...I am trying this again - hopefully someone can help me figure it out... I...
28
9 k
TNMike |
question
Can't Connect
I recently purchased the developers kit for my son. We made a simple roli type robot and tried to connect to the ez-b v4 for the first time tonight. I cannot get it to connect. As far as I can tell I need to change the connection mode, but when I click on the circular icon in ARC, it takes me to a page that asks for my username and password (unlike...
12
3 k
DJ Sures |
question
Continuous Rotation Servo
I installed a CR servo that came with my Dev kit. It works as it should in the ezb builder. I bought and upgraded HiTec Robot Servo model HSR-2645CR and when I try it it starts moving in one direction but then I cant control it. It wont stop or switch directions. I am using port D0 and have tried others and get the same problem. I have not tried an...
13
4 k
DJ Sures |
question
Ez-Script Control Re-Sizing Itself
@DJSures Of late I have noticed that the EZ-Script controls are re-sizing themselves when I reload a project. I will set them to a certain (small) size and save. When the project is reloaded, they have become wider and are overlapping. This makes it difficult to structure the controls as I would like. Have they been programmed to some minimum and...
16
4 k
WBS00001 |
question
Getdigital() Function Sets Digital Port On Rendering It Useless
getdigital() function sets digital port on rendering it useless. Tried on different boards. Will try from a different computer but if anyone has the same bug, please let me know. Updated ARC to last version. Thanks, Elfege
3
2 k
DJ Sures |