Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Kinect Xbox 360 Dept…
Converts Xbox 360 Kinect depth frames into NMS obstacle scans for ARC path planning, SLAM, and...
Kinect Body Control
Control robot servos with Microsoft Xbox 360 Kinect body tracking; map joints to upper/lower body...
Inverse Kinematic Ar…
Control robot arms with inverse and forward kinematics, converting X/Y/Z positions into joint motion...
Featured
Send web-triggered IFTTT events from ARC/EZ-B: configure Maker Webhooks key and trigger applets to control SmartThings, WeMo and other services.
Featured
Captain Ann Droid: a faster, smarter robot built on iRobot Create using EZ-Robot kit, software and Bluetooth speech for enhanced interaction.
question
Irobot Update
For those of you who have been following my build, I added a micro-servo to the EZB camera for up-down tracking. Now it self-adjusts for people of different heights. And it tracks...
2
2 k
Mac |
question
Sound Activated Circuit - Pc Vs. Ezb
I followed the tutorial to make the LED flash when my robot speaks. I noticed that if I have it set to the PC Speaker, the LED flashes in sync with the speaking but if I switch to the EzB, the flashing is not in sync and ends way before the talking completes. I am using the code from the tutorial (see below). # Sound Servo to PWM range Script #...
0
2 k
dbeard |
question
Connection Chime
Heya guys. Anyone know if its possible to disable, remove, or replace the "i have successfully connected to your network" chime from the connection startup?
5
2 k
WilliamK |
question
Servo Question
I have assembled my JD Humanoid Robot. When I connect to him, one of the servos makes a buzzing sound and won't stop unless I turn it off. For instance, the servo was the upper part of the...
9
2 k
drebant |
question
Can't Configure Rovi As A Wifi Ap
We are trying to reconfigure the Rovi to be a Wifi AP. We can connect to the Rovi via my router, we can access the Rovi's configure pages, both from my PC and my tablette, we can apparently save the "EZ-B Wi-Fi Access Point Mode Configuration", we then reboot the Rovi, either using its power switch or the reboot option from its Diagnostic...
10
4 k
DJ Sures |
question
2S Lipo Vs Servo
First I like to say that i'm very happy with your products But here we go A fully charged lipo puts out 8.2 volts and the servo's that are in the kits can have max 7.4 volts. I used in my projects cheap towerpro 995 servo's and a stepdown regulator to put out max 6 volts because if i put the full lipo voltage on them they begin to smell funny and...
2
3 k
ed_eilers |
question
Hb25- Initialzing Via A Power Cycle
I have had a little issue with using the Parallaz HB25 motor controllers I use with "Cy". Maybe someone could shed some light on this. It...
18
5 k
ptp |
question
Revolution Jd Connection Questions
Hello, I recently got a F-31 Revolution JD robot kit. I put the kit together and verified all the servos are connected to the correct ports on the...
6
2 k
jglavin |
question
Camera Grid Lines
I find when using the Camera, the grid lines change or fail to stay as set. I try to save the set locations of the lines, but when I reload the project I have to reset the grids again. Thanks, Ron
16
4 k
Andy Roid |
question
Face Recognition, Age, Gender And Emotion Sensing Video
Here is a video of the Face Recognition, Age, Gender and Emotion Detection system used on the ALTAIR Robots...
7
3 k
CochranRobotic… |
question
Script Question
Please have a look at this script. Will it run all the way through or will the Halt() command in the first "if" statement cause it to stop before it gets to the "Elseif" section? Thanks for looking. if ($ADC_Lft_Elbow => 160 )#160-350 is in Centered position $Lft_Arm_Centered = 0 #Reset varable 1=not cnetered, 0=centered...
12
4 k
DJ Sures |
question
Looking For Stl Files To Print
Hi, I am trying to find a download point for the STL files to make the servo mounts for a JD arm servo? Anyone point me in the right direction? Thanks Paul
6
3 k
DJ Sures |