Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Inverse Kinematic Ar…
Control robot arms with inverse and forward kinematics, converting X/Y/Z positions into joint motion...
PCA9685 Servo Driver
Convert an EZB I2C bus into a 16-channel PCA9685 servo controller, exposing V0..V15 with...
Rplidar
Slamtec 360° LiDAR driver: calibrated, offset/rotation-adjusted scans published to ARC NMS for...
Featured
Duplicate and synchronize commands from one master EZ-B to multiple slave EZ-Bs for simultaneous, mirrored robot actions.
Featured
Build a robot base with cheap hoverboard 3-phase motors and Flipsky FSESC VESC - programmable ESCs, servo connector, auto-config.
question
Telepresence Robot Idea
I would like to have my robot be controlled over internet with a Vr type Headset. Like one that you set the phone inside. I would tie the headset phone motions to the...
15
5 k
faengelm |
question
Radar And Rgb Dont Work
i read the tutorial tree times,try all kinds of stuff.bolt rgb and ping sensor dont work.i use an original roli ARC.the ARC disconnect when trying to use one of the rgb,got 2...
16
3 k
Nomad 6R |
question
Newbie Needs Help With First Robot
Hello, I've never posted in any forum before, so I hope I'm doing this properly. I've designed, 3D printed and assembled a robotic Gremlin using the EZB...
19
6 k
Nomad 6R |
question
Compressorhead
I saw this vid on another Inmoov site. For me, it is one of the best bot videos out there. The whole concept is wild, over the top, and just my style.
4
3 k
RoboHappy |
question
Tomy Omnibot
have in my possession a Tomy Omnibot for sale. Please contact me at 661-470-7815. [email protected].
2
2 k
DJ Sures |
question
Dead Battery
I have an AdventureBot that will not charge. Tried two different chargers and two different outlets. Tried charging for over 24 hours. Tried connecting and received a diagnostic report which showed N/A for voltage. I have a Roli and the same charger charged the battery in the Roli. I am assuming it is the battery that is bad in the AdventureBot. We...
3
2 k
bsletta |
question
Servo Shutting Off Ez-B
Hello, I have just bought some metal gear servos for the robot I am working on. When I go to plug in the servo into the EZ-B it just causes the board to keep shutting down. Is it drawing too much voltage or current? It is these two Kookye Servos: www.amazon.com/gp/product/B01I6AWBJI/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
8
3 k
Steve G |
question
Compatible Ssc-32 Controllers
I was reviewing the threads discussing the use of a SSC-32 controller to add an additional 32 servo (analog) ports. My question is if there are any specific...
4
3 k
bumsteadsean |
question
Power And Temperature
I am using scripting to get power and temperature for 2 ezb's. I have noticed that even if I disconnect the 2nd EZB, my script still shows power and temp for it even though it is no longer connected. I think there may be a bug in Ez Robot. Here is my script. $cputemp1 = 0 $cputemp2 = 0 $cpupower1 = 0 $cpupower2 = 0 $cputemp1 = ((GetCpuTemp(0) *...
2
2 k
dbeard |
question
Generic Answers To Any Question
Okay, this should be a fun one. So I’m all about AI, Chatbots and the like, but here I’m looking for something that does not use any of the above. So here it...
9
4 k
Steve G |
question
Script Help For Running And Stopped Mobile Image Buttons
Hey guys. I need a little script help with the mobile interface "Image buttons". I have two custom images I have made for one button... put simply, I have a green image for "script running", and a red image for "script stopped". I have the following script where if I press the image button once, the script runs....
7
3 k
Steve G |
question
Three Function Gripper
Hello everyone! I am an engineering student and I am currently making a robotics project that consists in building a three function gripper to be used in a robotic arm. I was given a few specifications that are quite different from each other. Basically I have to build a gripper that: Lifts 25Kg palets with 1200800140mm Lifts 30Kg cardboard boxes...
0
2 k
meclecca |