Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Rplidar
Slamtec Lidar driver for ARC; scans 360° and publishes distance data to NMS for mapping, obstacle...
Kinect Xbox 360 Dept…
Converts Xbox 360 Kinect depth frames into NMS obstacle scans for ARC path planning, SLAM, and...
Featured
Control Feetech serial-bus servos via EZB UART or PC COM, mapping servo IDs to ARC virtual ports; supports position, speed, release, acceleration.
Featured
Broostone Rover 2.0 telepresence robot with 7" Android tablet, teflon anti-tip sliders, servo-based stabilization planned and awaiting Ezb support.
question
Cool Claw From The Creative Mind Of Magnus
After reading the posts on Magnus I went searching for those cool claws he has and found this. At the Sportsman's Guide website for $50...
6
4 k
rgordon |
question
Using Multiple Pings Sensors
Using multiple pings sensors Hello all, I was pondering on how to configure multiple pings sensors. If I mount 4 ping sensors on all 4 sides of my bot, could I use...
3
3 k
DJ Sures |
question
Newcomer To The Ez-Bot Site.
Few things I wanted to mention, 1. Thanks for making it a very simple process to register! It's nice not to have to squint at captcha and guess at things and wait on registration confirmation emails, etc. 2. I found EZ-Robot.com through a suggestion made by someone on another forum and, although it is outside my price range and scope for my current...
2
2 k
DJ Sures |
question
LED For WALL-E's Eye
Hey guys, I tried to use the original LED that comes with the WALL-E U-Command with the EZ-B, but the LED does not turn on (using digital ports). Should the original LED work, or should I use another type of LED with the EZ-B?
19
4 k
okidey |
question
Omnibot Robot Wheels Rubber Replacement/ Repair
Ok so there are a couple ways to restore tires. The best is pulling one good tread off a wheel , make a plaster of Paris mold...
9
6 k
robotmaker |
question
Behind The Scenes
Wonder what it's like at EZ-Robot? It's not always fun and games - but when it is, we take advantage of it!
5
3 k
jstarne1 |
question
Nicd Battery Recommendation For Heavy Duty Servos
Can someone make a recommendation for rechargable NiCd battery for two high torque servos
1
2 k
jstarne1 |
question
Trex Motor Controller Problems With Ezb
I have several Pololu TReX motor controllers laying around. I hooked it up and connected a motor and a linear actuator to both channels. I started with an standard RC controller and made sure it was all set up. Worked fine. Then I replaced the reciever with the EZB. It worked for about 10 seconds then stopped. I had used PWM slider, then I tried...
16
6 k
fxrtst |
question
What I Would Like To See
Here is What I would like to see. A Radar for the Video Camera like we have for Sonar and IR. Would that be too hard to do? Let us know. That way, the Robot could be Autonymous using the Video Camera instead of IR and Sonar. Thanks, MEL
7
3 k
MovieMaker |
question
For Dj
Post Removed by MovieMaker Item Sold.
5
2 k
audioguy |
question
Segway Skateboard, Can Ez-Robot Use Imu Analog Combo Board
I saw this on youtube: https://www.youtube.com/watch?v=HGbbag9dklU here is his site:https://www.robosys.co.uk/ and here another how to make: https://www.instructables.com/id/Self-balancing-one-wheeled-electric-skateboard/?ALLSTEPS And it was right after I had just finished buying my EZ-Robot kit. My question is can the EZ-robot controller use IMU...
4
3 k
nyapaysolo |
question
ARC
Hello everybody, I own an EZ-V-B V3 Controler and would like some additional information concerning its use: At bootup, can the ARC be configured to connect to a specified port.com ? in order to automatically open a program / project. This info is necessary for use with a mini-itx motherboard destined for an autonomous robot project. Thanks in...
2
2 k
Romain |