All Community Content
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
PWM Servo Ramping
Smoothly ramps PWM servos on EZB D0-D23 via Vx-to-Dx mapping for natural, gradual motion without...
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Rplidar
Slamtec Lidar driver for ARC; scans 360° and publishes distance data to NMS for mapping, obstacle...
Featured
Balancing controller for Sainsmart v3 (and compatible) robots: PID tuning, real‑time telemetry, angle offset, movement and calibration via ARC.
Featured
Unboxing and assembly of a servo-equipped kit with servo alignment and the memorable captured moment
release
Windows Release 2015.09.27.00
Master Battery Monitor override in Connection Control requires agreement to assume LiPo damage risk; recheck and reconfigure Revolution robot monitor.
0
4 k
question
Using The B5t-Hvc Vision System
For testing I built a temporary housing for the B5T which also allowed me to add a tripod mount which makes things easier I have 4 faces currently registered...
11
5 k
nanomole40 |
question
Robot Mimicking Facial Expressions
You can watch it smile and make cute faces
5
3 k
WarPig |
question
@Dj-What Is The Link For The O-Scope You Use?
I want to get an O-Scope to use for troubleshooting. I seem to remember you have a small o-scope that you like to use to look at servo signals but I can't find the forum discussion where you gave the link.
1
3 k
Jeremie |
question
Set On/Off On Ssc-32
How can I set the virtual ports on the SSC-32 to on or off? Doing Set(V0,On) doesn't do it which I don't get as you can control a servo using Servo(V0,90), or, like servo speed, is this not supported either?
8
3 k
Steve G |
robot
Ashmcfarlane's I Would Like To Create A Robot
Assistive home robot for visually impaired: voice-recognition control, vacuuming, camera object/danger detection, and home monitoring with Ezrobot.
0
2 k
ashmcfarlane |
question
Trouble Connecting 2 Ezb's
I'm trying to connect two v4's in one project, but no dice. I know someone had this trouble before, but can't find the thread. They are both set to client mode, and the...
29
6 k
Steve G |
question
Automating A Rc Car
I have a RC rock crawler that I would like to automate and turn into a Robot . If I but the EZ-B v4 Developer Kit will I be able to replace my receiver on my car with the Ezb-v4 unit and hook up my steering and ESC servos to run and stear the car through the programming to the . The car has 7.2 v Battery system on board which come through the ESC....
7
3 k
DJ Sures |
question
Ssc-32 Speed Control
I'm currently installing and testing my new SSC-32 and testing servos using Servo(V0,xx) script commands which work great, and I'm trying to get a "connection" init script sorted to set virtual servo speeds on start up, but can't figure out how to control speed. A take it that the "ServoSpeed()" commands are not supported for...
9
3 k
Steve G |
robot
Theguitarguy's A Robot That Can Aid In Organi
Robot that organizes your desk while you're away, with a camera streaming live progress to your smartphone.
0
2 k
Theguitarguy |
question
Ezb V4 Short Circuit
I have a problem with my EZB. Its connected to a JD-head. That means 2 servos, rgb Eyes and camera. Powered with a 2cell lipo with a 2 Amp fuse inline. I had the EZB powered up and programming, shut it down to eat dinner. When I got back i plugged it in again but it didnt boot, 10 seconds later the 2 amp fuse was blown. I unplugged everyting from...
2
2 k
James Graham H… |
question
Longer Programming Time
i made a video how you can use an extended batt 2200 or 5000MaH with 12 servo's .you will only see the female jack. tell me what you think plzz. 5000mah 2200mah
5
3 k
Nomad 6R |