All Community Content
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Inverse Kinematic Ar…
Control robot arms with inverse and forward kinematics, converting X/Y/Z positions into joint motion...
PCA9685 Servo Driver
Convert an EZB I2C bus into a 16-channel PCA9685 servo controller, exposing V0..V15 with...
Rplidar
Slamtec 360° LiDAR driver: calibrated, offset/rotation-adjusted scans published to ARC NMS for...
Featured
Control Feetech serial-bus servos via EZB UART or PC COM, mapping servo IDs to ARC virtual ports; supports position, speed, release, acceleration.
Featured
Scout robot from a 14-inch Mega-Byte thrift-store toy; modified servos, one stripped gear, budget DIY home driving.
robot
Ezang's Some Examples From The Past Of Glyphs, Glyphs With Augmented Reality And QR Codes
Glyph examples with augmented reality and...
0
2 k
EzAng |
robot
Ezang's New Robot Head Video Project 6/15/2021
Robot head teardown and component breakdown from 6/15/2021, revealing build details and assembly insights
4
3 k
EzAng |
hardware
Lattepanda
LattePanda runs Windows and Synthiam ARC, with onboard Arduino (EZB firmware) for GPIO and direct EZB v4 hardwire control with low latency.
31
21 k
question
Min Voltage For IO Tiny
I am working on the T3-DO project from Michael Baddeley Printed Droid. I am planning on using the IO Tiny with MG90 and FS90R servos. These are basically max 6V servos. Does the IO Tiny regulate voltage? My guess is no as I am pretty sure the EZ-BV4 does not either. So, what is the min voltage for the IO Tiny? I don't want to use the EZ-Robot...
3
2 k
MarkTheBotBldr |
question
Connecting A Iotiny/PCA9685 Together?
Was wondering if anyone has connected a PCA9685 to a ioTiny? I am building a robot head for my grandson. Have a extra ioTiny and PCA9685 lying around here and would like to use them. The head has 13 servos, the ioTiny 8 ports, not going to workie! Was hoping I could connect them together for enough ports! I don't want to spend too much on this as I...
4
2 k
Proteus |
question
Why Does A Windows Volume Slider Pop Up On ARC?
Does anyone know why I have a Windows Volume Slider pop up on top of ARC? It will pop up in the upper left corner by the menu....
6
2 k
Dave Schulpius |
question
Setup OLED I2C Display With EZ-B V4
I need help with setting up an I2C OLED display with the EZ-B v4. The display is connected to the EZ-B v4 based on my understanding of the pin outs on the EZ-B I2C slot as per the manual. The display doesn't seem to light up (not sure if it should) and I have no idea which skill I use to enable sending of text and EZ-B display information to the...
15
2 k
gjohal |
question
EZB Not Responding
Can't get ECB to connect? I'm getting the EZB Not Responding error. "Unable to connect to 192.168.10.1:23. This PC apperas to be connected to a network with the IP address that was specified. However,, the connect could not be established with the EZB." The EZB Wifi network is running. I turned Norton Anti-Virus on and off. Same problem...
12
2 k
DJ Sures |
question
Connect To A Secure MQTT Broker
Hi everyone, I have a MQTT cloud service, deployed on Amazon Web Service. It has secret credentials like username, password & client Id. My question is: on EZ-robot MQTT client, how to connect to a secure MQTT Broker using username, password & client Id? Also how to configure the qos (quality of service)? How to configure these credentials...
2
2 k
lintangwisesa |
robot
Ezang's My New Whirlybird Project For You To View
Whirlybird showcase: a new Servo City ARC robot project highlighting servo-based hobby robotics
6
3 k
EzAng |
Servo
Servo Pad
Drag mouse or finger as a virtual joystick to control pan/tilt x- and y-axis servos with configurable ports, limits, inversion, and...
5
6 k
question
Anyone Building A Full Size R2D2 From Mr. Baddely Design?
Synthiam/ARC users, I now have some series 3D printers and I am starting to build a full size R2D2 unit working with this designer who has a FB page.... https://www.facebook.com/groups/MrBaddeley Most R2 builders use Padawan 360 build which is based on Arduinos and various other components. I am thinking about implementing an ARC build using an...
6
2 k
onedayflie2 |