All Community Content
Synthiam Credit
Log In
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Synthiam Swag
See All Swag
"I build robots" Hoodie
Recent Robot Skills
View All
Autonomous AI
Autonomous AI robot skill for ARC: vision-based LLM control, speech, movement, animations, memory,...
PWM Servo Ramping
Smoothly ramps PWM servos on EZB D0-D23 via Vx-to-Dx mapping for natural, gradual motion without...
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Featured
Autonomous AI robot skill for ARC: vision-based LLM control, speech, movement, animations, memory, drives, and multi-step autonomous tasks.
Featured
JD backpack mockup anchors into JD's middle slot with male clip, two top posts, dual rear mounts, wire access and switch opening.
question
Robot Ower Supply Help Please?
Not sure if this is outside the scope of this forum or not. If so, my apologies in advance. I'm modifying my life size Lost in Space B9 robot from static...
10
5 k
gwen4156 |
question
Setting Up Jd
I am having problems with JD. I charged him up for 2 hours, until the green light went out on the blue Balancer Charger. When I turn him on the following happens: 1. Light blue light appears in...
8
2 k
dmcgreal18 |
release
Windows 2014.10.09.00
ez-bit library improved sync performance; updated JD project with minor GUI enhancements and fixes.
1
4 k
Luis Vazquez |
question
Need Help
Sorry but may i know why my auto positions aren't working in the mobile interface but only the camera is working? i've checked the ports and are connected properly.
15
4 k
ezrobot3 |
question
#D Printer
Hello all, I have a 3D printer and would like to know if I can add it to help people print if they need the service. Most cases I am willing to trade for help programming, since I am not very good programming yet. stress
10
4 k
Redzone |
question
Questions With ARC Ui
The buttons on ARC are cut off and a lot of the text is extremely small. Does anyone know how to fix this problem? I'm using a 3200 x 1800 monitor which might be the cause.
18
6 k
CardboardHacke… |
tutorial
I2c Ezb Arduino1 Sensor
Use an Arduino as an I2C sensor controller with EZB3/4 and EZ-Builder to read ultrasonic sensor pings via I2CRead.
0
3 k
Luis Vazquez |
question
R2d2 Sounds
If you want to create "R2D2" sounds for your 'bot, look at: https://www.r2d2translator.com
3
3 k
Luis Vazquez |
question
Accelerometer And Gyro Confusion
I think I may have got my self a little confused. What's the difference between an accelerometer and a gyro? Does an accelerometer return the movement of each angle or the angle itself?
8
2 k
Luis Vazquez |
question
Movement Of Jd
I bought JD from the internet site and it arrived. After I built JD according to the instructions I could do with the robot everything; the led eyes, the sound, the camera, everything except the movement. can someone help my with that? please advise how can the Robot move, walk, etc. @DanielKal [email protected]
10
3 k
Rich |
tutorial
Using The Sure Dc Ss503v100 With Ezb4
Configure Sure DC SS503V100 compass with EZB4 over UART: wire RX/TX, set OPT high with 3.3V, use EZB4 3.3V power for UART mode
0
4 k
Luis Vazquez |
question
Question Do I Have A Bad Servo? Or Tell Me How To Fix It
Question Do I have a bad servo? Or tell me how to fix it... Listen to video... j stress stress stress...
8
3 k
A.Bautista |