All Community Content
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Autonomous AI
Autonomous AI robot skill for ARC: vision-based LLM control, speech, movement, animations, memory,...
PWM Servo Ramping
Smoothly ramps PWM servos on EZB D0-D23 via Vx-to-Dx mapping for natural, gradual motion without...
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Featured
ARC UI for onboard computers to control NeoPixel rings via serial: test/run patterns, preview and copy Arduino serial commands, includes sample code.
Featured
ARC robot software enables next-generation robotics with intuitive tools to build, script, control and troubleshoot advanced robot skills.
question
Bad Servo?
Servo was working fine. Shutdown JD. Then when restarted JD found a bad servo? See pictures: See red area: J stress stress stress stress
3
3 k
Nomad 6R |
question
Finger Tip Sensors For Inmoov Hand
@Richard R. Are you going to use the finger tip sensora on your inmoov? I'm printing a new hand and would like to make use of the sensors but I don't...
10
6 k
Dave Schulpius |
robot
Zooboy318's A Robot That Is An All-Around
All-around helper robot cleans, filters air, sorts laundry, feeds pets, entertains with music/games, monitors home via camera/motion alerts and EMF.
0
2 k
ZooBoy318 |
question
Additional ARC Requests
Hi. I have a couple of ideas for the EZ-Robot team to consider that I think would be a nice addition to ARC. 1. When adjusting the volume slider from 100 on an EZ-B soundboard, say to about 60 for example, when a project is saved, closed, and reopened the volume goes back to the default 100. Would it be possable to add the ability to save the the...
11
4 k
Steve G |
question
Can I Change The Default Directory That ARC Defaults To?
I'd like to use a different default directory for saving my files and getting the examples. Is there...
5
2 k
Wolfie |
question
Additional Batteries For Jr
Why not put batteries in the feet of JR to extend his running time? A little mod to the feet profile and could put 1300maH in each foot. Or maybe extend the other part of the body to put in 2 other 1300's Just some thoughts
3
2 k
Morbeious |
question
Autoposition - Dc Motors & Servos
I have to admit I have not tried the AutoPosition control. It's still a bit of a mystery to me but I plan on diving into it in a few days. I've been focused on building a 7 pound arm with 4 joints for my B9 Lost in Space robot. I've now got it working smoothly; twisting and turning and lifting the weight. The first "elbow joint" lifts all...
8
4 k
Dave Schulpius |
question
Six & Jd Losing Wifi Connection From A Distance
I have always had limited Wifi Connection since I received JD. I recently bought Six & it also has limited Wifi Connection. Both work fine close to my router but last night I moved both in another room to show friends & both started. Then, Six quit & JD went crazy! I am assuming that I lost Wifi on Six & I don't have a clue why JD...
3
2 k
michaelc |
question
Need To Put Robot Back In Direct Wireless Connection
I was having trouble getting the robot to connect to my computer ( only the camera would work.) so i changed the...
16
4 k
thetechguru |
question
Defective Servo?
Hi, I have Six and it was working perfectly until just recently. One of the servos doesn't seem to be getting a signal or isn't responding. It was on port D1 so I swapped it for the servo on port D4. No luck. I opened it up to see if there was an obvious issue. All of the wires are soldered to the board. Any suggestions?
4
3 k
tom.caine |
question
Rgb Panels
Gang, Has anyone tried this or other RGB Panels with Ez-Bv4? www.karlssonrobotics.com/cart/RGB-LED-Panel-32x32/?gclid=Cj0KEQiAiO-kBRCNxtaJp4-En6sBEiQAnkvW37h5EG6fGD_YixKDJsPGBRAyh_UIGq4YbwhXyfolXTEaAlFw8P8HAQ
0
3 k
Morbeious |
question
Tilt/Pan Parts
Gang, Has anyone seen or create tilt/pan 3d parts in stl format to be use with the dev kit camera?
8
3 k
Morbeious |