Robot Building Questions
ARC Pro is more than a tool; it's a creative playground for robot enthusiasts, where you can turn your wildest ideas into reality.
Synthiam Credit
Your Synthiam Credit is $0.00
Discover ways you can lower the cost of Synthiam products by contributing to the platform and community.
Earn Synthiam Credit
Exosphere
Loading...
Add Remote telepresence to control any robot from your phone or PC
Add your robot to Exosphere
Sythiam Swag
Gaming Mouse Pad
While programming your robot, these 9x7 inch personalized mouse pads deliver a smooth experience with a custom flair....
Recent Robot Skills
ZAMA Emotion Model
Valence-arousal emotion engine generating persistent, configurable robot moods and event-driven emotional...
Feetech RS485 Servo
Control Feetech serial-bus smart servos via EZB UART or PC COM port; map ARC virtual ports to servo IDs with...
Feetech Serial Bus S…
Control Feetech SC-series serial-bus servos via EZB UART or PC COM. Map ARC virtual ports to IDs; supports...
Featured
Use camera-detected printed cue cards (direction, pause, start) to record and run stored movement sequences for ARC robots.
Featured
Victor Vac: Roomba-based EZ-Robot with EZ-B v4, sensors and Synthiam ARC scripting for autonomous vacuuming, voice, media and home monitoring
question
Contact With Other Users
Hello, My name is Jim . Is anyone in the Eugene Oregon area working with ARC & EZ Script. If so please let me know .Maybe we can connect .
4
2 k
sadi heric |
question
Face Rec
Can the EZ v4 recognize individual faces like your mother and then say "hello Sue" Thanks
1
2 k
thetechguru |
question
New Star Wars Robot
Check out the new robot that will be on the upcoming Star Wars movie.
6
4 k
Antron007 |
question
Syntax; Return()
:pingtest Goto(SonarTest) say("Distance" + $Distance + "inches") sleep(5000) Goto(pingtest) :SonarTest $Distance = Round(GetPing(D9,D8)/2.54,0) if(1 < 1000) sleep(25) Return() endif goto(SonarTest) So, it's apparently been too many years since I've attempted to write some code, as I'm getting stumped pretty easy. Can...
2
2 k
R1D1 |
question
Body Frame & Head Change On: Ez-Robot Jd
Hi all & DJ Spent a good amount of time researching what Robot to purchase, choices were; 1. NAO 2. Robi 3. DarWin 4. EZ-Robot JD 5. Pepper Happy to announce my choice was EZ-Robot JD!:-) Now; we will be working with children who have extream hypersensitivity & ADHD, teaching them how to make apps & run JD. Using JD with children who...
4
2 k
Clip2Trigger |
question
Wall-E From Junk
Remember the guy who made a DJ robot from flattened plastic water pipe? Well, he's still at it, making a Wall-E from stuff and such. A Wall-E from junk seems kinda fitting to the Wall-E meme, actually. https://www.instructables.com/id/Robot-real-size-LowCost-walle-made-from-water-pipe/
3
3 k
DJ Sures |
question
Battery Not Charging
after setting it up, and testing it. the next time I wanted to continue my test the battery is unable to charge. the 3 red LED keep on blinking. I disconnect the other connection...
6
2 k
Jit |
question
How To Control Dinamixel Servo Type Rx-64 With ARC
I have a servo dynamixel type Rx-64 with 4 wire (vcc, Grn, D-, D+) I am confused to programming using ARC , do the servo...
4
3 k
Steve G |
question
Low Battery Alerting Incorrectly
I've had EZB4 for about a month now and has been working great until today. In the Desktop Connection settings, I changed the Min Voltage for the Battery Monitor to 5.2, as I'm powering my EZB with a 6 volt battery. I did this a few weeks ago and everything has been fine. Now today, when I'm using my Mobile Interface, I keep hearing the "My...
3
2 k
R1D1 |
question
Ez-B V4 Wi-Fi Robot Controller
I am using the EZ-B v4 Wi-Fi Robot Controller to replace the receiver in my RC car and make it into a robot . The 7.2 V battery powers both the motor and is connected to the ESC which then plugs into the receiver and powers the receiver also . The other servo for steering is also powered by the connection of the ESC to the receiver . Can you tell...
11
4 k
bhouston |
question
Jd - V3 Or V4 Controller?
I bought JD when he first came out! I am seeing some v3 & v4 controller info. Has EZ-Robot already changed to a v4? How can I tell if mine is the v3 or v4? Does the v3 still work with all the program upgrades? Thanks.
3
2 k
michaelc |
question
Servo Release Not Working Using (D#,0)
@DJ and Jeremie. I've been setting up some servos, and I've noticed that the servo release using (for example), Servo(D5,0), the zero is now being treated as a servo holding position as it was before the introduction of zero being a servo release. I am using the latest ARC version, (2015.09.00), and it was working a few weeks back. I also tried it...
17
5 k
Steve G |