Robot Building Questions
Experience early access to the latest features and updates. You'll have everything that is needed to unleash your robot's potential.
Synthiam Credit
Your Synthiam Credit is $0.00
Discover ways you can lower the cost of Synthiam products by contributing to the platform and community.
Earn Synthiam Credit
Exosphere
Loading...
Add remote telepresence capabilities to your robot from your phone or PC
Add your robot to Exosphere
Sythiam Swag
Gaming Mouse Pad
While programming your robot, these 9x7 inch personalized mouse pads deliver a smooth experience with a custom flair....
Featured
On Variable Changed
This skill will execute a script when a variable has changed.
Featured
AVA advanced visual android
Hello Again pheww the robot legs are done and ready to 3d print each joint uses a parametric slew motor which are driven by 550 type dc...
question
Relay Driver Using An Arduino To An Ezbv4
Hello All, I have an 8 relay 5volt relay board, (compatable with Arduino) which I want to drive from my EZBv4. I have made a script to run...
14
4 k
Andy Roid |
question
Remote Control Robot Omnibot 2000
Hello everyone, I am looking for a remote control robot OMNIBOT 2000 quelquin peutil inform me where I can buy one?
2
2 k
bernard eric |
question
Sync To Ez-Bit Library
I have been able to connect the bot to the wifi. I also have an internet cable plugged into my laptop. When I try to sync to EZ Cloud I get this: Unable to COnnect to EZ-Cloud. Please connect to the internet. The server committed a protocol violation. Section=ResponseStatusLine Can someone direct me towards my next steps?
2
2 k
campbell.eric |
question
Smartphone In Robot
video camera robotsmartphone
10
4 k
Nomad 6R |
question
Whether Does Voice And Hearing Functions Support Chinese?
Hello all. Excuse me,I want to know whether voice and hearing functions support Chinese?Such as I can make voice communication with DJ robot in Chinese? chao
2
2 k
yc534092571 |
question
The Connection Is Not Firm Between Ez-B V4 Tobot Controller And Body
The connection is not firm between EZ-B v4 tobot controller and body.It was...
4
2 k
thetechguru |
question
Newest Version Of ARC Cannot Install
I just downloaded the newest version of ARC, when I go to install it, Windows is telling me its not a valid installer program? I am running windows 7. Thoughts?
5
2 k
WayneA |
question
Variables Not Global?
So, I thought I read somewhere in the forums that the variables that I create are all global. I wrote an initialize script that I run before any other script once I power up my EZB4. This script is for the purpose of declaring all of my variables, among other things. I wrote another script that would not work. It contains variables that are...
6
2 k
R1D1 |
question
Forum Converts Http Links To Https
When embedding links into forum posts, the post shows up with the link converted to https, REGARDLESS if you used plain http for a REASON. This is not wise since not all sites are HTTPS capable and this leads to bad links and user confusion. It should use the scheme provided by the user and not blindly change it. example: link that gets converted...
6
2 k
eXtace |
question
Servo Burning Out
I was showing my wife for the first time how to position Six. and as we were working on it. I smelled that electrical smell you get what things are not going right. looked down and the...
11
6 k
Dave Schulpius |
question
Compile Ez-Sdk
I have a problem when I compile EZ-SDK The error below: c:\Windows\Microsoft.NET\Framework\v4.0.30319\Microsoft.Common.targets(1605,5): warning MSB3274: The primary reference EZ_B could not be resolved because it was built against the .NETFramework,Version=v4.5 framework. This is a higher version than the currently targeted framework...
5
3 k
danbachmann |
question
Print Settings For Cubify Cube Gen3
Hi, I have a Revolution JD on order and just wondered what the recommended print settings are for both ABS and PLA. I printed a test foot using PLA on the highest settings 70 microns, almost solid and honeycomb, was this correct? Thanks in advance, Paul.
1
2 k
DJ Sures |