All Community Content
Synthiam Credit
Log In
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Synthiam Swag
See All Swag
Robot Sticker
Recent Robot Skills
View All
Autonomous AI
Autonomous AI robot skill for ARC: vision-based LLM control, speech, movement, animations, memory,...
PWM Servo Ramping
Smoothly ramps PWM servos on EZB D0-D23 via Vx-to-Dx mapping for natural, gradual motion without...
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Featured
Control Kondo KRS ICS2/3.5 servos via EZ-B UART; experimental, untested. Supports chaining, virtual servo ports, Release() and Servo() commands.
Featured
EZ-BOB: rebuilt from Arduino BOB Frizby with glowing red LED eyes, series resistors, lopsided compact DIY conversion
question
Roomba Pre-Defined Controls Via D0 On Ezb(4)
Are the pre-built controls within EZB going to be able to utilize any other UART ports or hardcoded to use D0 only on the new EZB(4) ?
3
3 k
Dunning-Kruger |
question
I Hook Up To My New Ezb Camera And The Light Comes On, But It Does Not Show A Pi
It does not show a picture in ARC. Do any of you have any...
20
5 k
MovieMaker |
question
Uart Port Voltage
Looking at the EZB spec sheet the UART TTL Voltage Level (input/output) is listed at 3.3 volts. I am going to connect that port to a device that uses 5V TTL for communicating via serial. I believe I would have to use a bidirectional logic level converter. Am I correct? Thanks
13
5 k
MovieMaker |
question
So, Who Has Recieved Their Developers Kits?
Hello everyone :-} I was just wondering who has received their developer kits, since they supposedly have already been sent out, I am...
79
11 k
stonewolf |
question
Continuous Servo Direction Change
So I am sure someone else has this some place ( i cant find it ) but I am just getting started with my EZ B (super fun btw) but I am having a silly issue getting the 360 servo to change direction i have the panel up but when I hit other arrow it does not switch... I can only get it to go one direction and stop... both arrows send it in same...
10
5 k
Jayutmb |
question
Questions About Battery 7.4Vdc 1300Mah Sold By Ez-Robot
Questions about Battery 7.4VDC 1300mAh sold by ez-robot Does anyone have one? How long does it take to fully change? J
17
5 k
Steve S |
question
Connection Question On Mobile
I get to the point where I am to connect on my Galaxy Note 3 and EZ-B does not show up on the choices for WiFi connections. I also cannot disconnect my Note 3...
8
3 k
bookmaker32 |
question
Wifi Connection
hi there, my EZ B is not showing up on my systems WIFI serch, why is that?
9
3 k
mgodsell1973 |
question
Cloud Question
Get this error while attempting to access cloud, logged in as normal,verified password ets edit # My user settings say no files saved in cloud,but mobile phone can access them
2
3 k
Bravia |
question
Servo Speed
I have two questions #1 - what are the values that make the continuous rotations servos go slow? For example 90 is to fast but I can seem to figure out what the range from real slow to real fast is. #2 - could someone provide me an example script that would drive the robot forward at the speed determined by a value in a script. Thanks.
8
3 k
dbeard |
question
I See Men In Black
I see men in black... j
15
4 k
CochranRobotic… |
question
Stepper Motor Speed And Pwm
Hi guys, Here I am back in bewilderment land. I am trying to run a stepper motor with a Spark Fun Big Easy stepper motor driver. No problem except no matter what PWM...
19
7 k
jstarne1 |