Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Inverse Kinematic Ar…
Control robot arms with inverse and forward kinematics, converting X/Y/Z positions into joint motion...
PCA9685 Servo Driver
Convert an EZB I2C bus into a 16-channel PCA9685 servo controller, exposing V0..V15 with...
Rplidar
Slamtec 360° LiDAR driver: calibrated, offset/rotation-adjusted scans published to ARC NMS for...
Featured
Overhead camera tracks a glyph to give precise robot pose to ARC's NMS for multi-camera indoor/outdoor navigation and waypoint control
Featured
Unboxing and assembly of a servo-equipped kit with servo alignment and the memorable captured moment
question
Robosapien Wowee Sensor
Good morning, Anyone know what the syntax for the ultrasonic sensor and sesnsor touch the feet and hands of Wowee Robosapien? Fart is: Robosapien (Fart). and ultrasonic sensor and sensor touche? Would anyone know?
7
2 k
Rich |
question
Questions About 3D Printing
Question who on the internet is providing 3D printing? (I do not own a 3D printer). 2nd question can you request different colors for the parts? 3rd question how do you make a list of parts from ARC? I am starting a new project called: Zippy! (aka EZ-Robot Hexapod, code name Six!) Or should I just wait for a kit from EZ-Robot Inc.? Thanks in...
4
3 k
jdebay |
question
Anybody Here Worked With Mimo 7 Touchscreen
I installed the drivers for the Display and they worked GREAT. I installed drivers for the touch screen and NO TOUCH SCREEN. I have installed them over and over again about 12 times with full shutdown and reboot. My computer is an AspireONE by acer. It is brandnew with Windows7. I installed the vista drivers just to make sure they did not work. The...
2
2 k
MovieMaker |
question
The Workbench Is Clear?
I noticed that the front workbench is cleared off. What's going on?
5
2 k
Mark |
question
Out Of Stock
Any idea when the The EZ-Robot Complete Kit will be back in stock?
12
4 k
Mark |
question
2S Lipo Battery Monitor
As also posted in my Hearoid showcase topic, but useful for anyone running LiPo batteries (could be adapted easily for 3S and 4S without too much of a problem). Parts needed:...
19
12 k
Rich |
question
Df Robot L298p Twin V1.1 Motor Shield
Has anyone had any experience with this motor controler. Is a DF Robot L298P-Twin V1.1. I went to DFrobot.com and couldnt find any info on it....
11
8 k
woodylv |
question
Pololu Maestro Servo Controler
Has anyone used the Pololu maestro servo controller with their ez board? I have 25 servos and 3 stepper motors sitting on my desk waiting to be used. I was going to power the servos and steppers separately from my ez board when I came across the maestro controller while looking for stepper controllers. I'm new to robots but planed a class research...
5
3 k
Rich |
question
Do I Need Resistors
Hi My MMA7455 Accelerometer finally dropped through the letterbox today, thank goodness. But now I have a question. A few i2c examples have shown that resistors are needed. Some...
6
2 k
Jaychadw |
question
First Impressions
I arrived in Calgary, Alberta, Canada on Tuesday July 15th, 2013 with the DJ and the entire EZ-Robot team waiting to pick me up at the airport. After a quick introduction to everyone, I...
15
4 k
Niek |
question
Using Newbright Chasis For Ez-Robot Locomotion
I got a couple of newbright 12.5" monster trucks "raminator" Was looking to plug the chasis into the ez-b. So i...
15
4 k
PJ_Dtechy |
question
Version Conflict
I'm attempting to connect to my EZ-board but keep getting the message I'm running version 8 OS but the board requires version 16. I've downloaded and installed the latest OS twice and rebooted but it doesn't upgrade. Any suggestions? Thanks, Daniel
2
2 k
Mulberry |