All Community Content
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Autonomous AI
Autonomous AI robot skill for ARC: vision-based LLM control, speech, movement, animations, memory,...
PWM Servo Ramping
Smoothly ramps PWM servos on EZB D0-D23 via Vx-to-Dx mapping for natural, gradual motion without...
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Featured
Fetch RSS via GetRSS command; populates $RSSSuccess, $RSSErrorMsg and arrays $RSSTitles, $RSSDescriptions, $RSSLinks, $RSSDates for scripts.
Featured
Hack and modernize NES ROB using Synthiam ARC and EZ-B: RGB eyes, servos, IoTiny, LiPo, speakers, motors, scripts, 3D upgrades and Power Glove...
question
Robi Has Come Alive
well.. after long looking i found the error. now he and me needs to practise japanes alot. thanks to dj ,he gave me the tip where to look.
6
3 k
Nomad 6R |
question
Ez-B V4 Robot Brain Overview
I believe that the ports are ADC ports are labeled wrong. Goto Learn - Developers Kit - Section 2 Ez-B V4 Robot Brain Overview. Shouldn't ADC0 Be at the bottom near...
3
3 k
Nomad 6R |
robot
Abeiku's ROBOT ARE THINGS THAT WILL SAV
Robots that save and assist people, exploring ways to create more helpful devices.
0
2 k
abeiku |
question
Servo And Ultrasonic Sensor
I have the Sensor hooked up on D0 and D1. It works fine. I have the servos on D4 and D5. When I try to move the Robot it fries the sensor. The sensor goes to 255 and never works again. Is there some rule of thumb about how many ports they should be separated? Or is there something else I need to do to make it so I don't fry any more sensors?...
2
2 k
dbeard |
question
I2c Connector Information
Does anyone have a source for the i2c connector/cable in the states? I can't seem to find it at the re-sellers listed at the ezrobot shop. Or a connector name eg. JST-PH?
19
4 k
Nomad 6R |
question
New Emaill Address
Need help, How do I update my email details in side my account details etc thanks
3
3 k
Nomad 6R |
question
![How To Connect Your Ez-B V4 To Your Computer(Both Ways[Ap And Client])](/uploads/thumbnails/2265.jpg)
How To Connect Your Ez-B V4 To Your Computer(Both Ways[Ap And Client])
I made a few How-to videos showing people how to connect the ez-b v4 in both Ap...
36
12 k
tevans |
question
Time Lapse With A Gopro
Here's a video which shows how you can use a GoPro for time lapse photography with Roli. - https://www.youtube.com/watch?v=IreUCKTxbbg Question - which control is being used?...
7
3 k
Stika |
question
Advice Needed For Computer Courses
Guys, need some help... I feel that I know a fair bit about robotics however I am held back by my lack of computer knowledge in general... I have actually had a few job offers after my inMoov video but I turned them down because I am a bit of a dumb a** when it comes to computer knowledge... I can't very go into an interview if the HR guy asks me...
21
7 k
Dunning-Kruger |
question
Ez4 Controller
To whom it may concern if I purchase the head of JD with the camera to use on another platform do I need to but the EZB Controller in order for it to work?
10
4 k
Jerseylance |
question
Query Regarding Ez-Script-Help.Pdf
Hello Please can you check the EZ-Script-Help.pdf file for the two possible amendments : Under REPEATWHILE example : should "REPEATUNTIL" be replaced with "REPEATWHILE" and Under GetServo and SetServo : should "100" be replaced with "180" Thanks Ian
3
3 k
Dunning-Kruger |
robot
V692's My 1St Build With Ez Robot Dev Kit.The Lawn Bot (Build Log)
Lawn Bot hauls barrels, mows in summer and snow-blows in winter using a 24V Jazzy wheelchair base with Jazzy VR2 controller and EZ-B4
8
3 k
thetechguru |