Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Rplidar
Slamtec Lidar driver for ARC; scans 360° and publishes distance data to NMS for mapping, obstacle...
Kinect Xbox 360 Dept…
Converts Xbox 360 Kinect depth frames into NMS obstacle scans for ARC path planning, SLAM, and...
Featured
Overlay translucent PNG targets onto a camera stream with loadable templates, attach/detach control, preview and status for visual alignment.
Featured
Custom Hulkbuster Iron Man suit with servo helmet lift, glowing repulsors, sound effects, 3D fit measurements and EZ-Robot electronics control
question
At What Baud Rate Does ARC Run?
What is the baud rate of ARC? What's the board's default baud rate?
3
3 k
DuxDucis |
question
H-Bridge, 1 Motor, Seperate Battery
Hi, I'm sorry if this has already been handled in other threads, i have a quick question about the 2.5 Amp Motor Controller from this website. I plan...
3
3 k
Dave Schulpius |
question
Price Just Dropped In The Ez Store!
Check it out. 2/2/13. Good prices! Ya gotta love this place! Edit: I see it was actully a few hours ago and other threads mentioned it. blush
0
2 k
Dave Schulpius |
question
Camera Right Tracking Question
Camera Right Tracking problem. Hello, The tracking is ok if the object moves to the left of the screen, but does nothing if the object moves to the right. There are a few weeks everything was perfect. I have ARC 2013.1.30 and firmware V16.
2
2 k
clode |
question
Smooth Servo Movements
I noticed that a lot of robots on here don't have fluid movements, rather very jerky and not dynamic. Is this due to mechanics, servo, programming or everything in between?
5
3 k
DJ Sures |
question
Script With Controlcommand And Camera - Error Message
Hi, I have written a script using the camera for face tracking, which used to work ok. But now, at the begining of...
15
5 k
DJ Sures |
question
Operating System Question
Can EZB run under Linux? I am thinking about a mini single board on my robot to make it automonius (excuse the spelling) and have speak ect on board rather than coming from my desktop. The Strawberry PI runs a version of Linux and is quite inexpensive. Thoughts? jms
4
2 k
DuxDucis |
question
Servo Speed Control
Having problems with speed control and couple other questions some one may have answers to. 1. EzB_Connect1.EZB.Servo.SetServoSpeed(Servo.ServoPortEnum.D3, 90). Does 90 mean 90% of power. If so it is very slow. I notice that in the Servo Speed Control it uses 0-9. The lower seems to be the faster speed. Do I use 0-9 for the VB command? 2. How do I...
1
3 k
DJ Sures |
question
Contolling The Bioloid Cm-5 Controller
How can I use the ez -B to send commands to the Bioloid CM-5 controller. Thanks
4
3 k
jstarne1 |
question
Yarp Port
implimented ezb to yarp need image matrix to get salience and advance object recognition and various other ports to get it the ability to get complex stuff and off load other things to multiple computers
0
2 k
Mike2021 |
question
Anyone Available To Do Ez-Script Scripting Examples ?
Friday, 1 February 2013 Good Morning Fellow EZ-Robot Scripters ! Is anyone available to colaborate on EZ-Scrpts and write simple Test Code Examples to become familar with Using the EZ-Script Instruction Set ? Hopefully, we can do it by this Forum, if that is permitted, or Phone, or Skype, etc. Thank You & Best Wishes From Phoenix,...
5
3 k
DougPope |
question
Ez-B Does Not Power Up.
if i connect power to the ez-b the leds don't light up. yesterday i had the same issue, and fiddled around a bit thinking there might be a loose connection. Randomly it did power up, but today i cant get it to work anymore. What could be the problem here, i cant see any obvious disconnections, how should i diagnose?
19
3 k
robotmaker |