All Community Content
Harnessing the power of ARC Pro, your robot can be more than just a simple automated machine.
Synthiam Credit
Your Synthiam Credit is $0.00
Discover ways you can lower the cost of Synthiam products by contributing to the platform and community.
Earn Synthiam Credit
Exosphere
Loading...
Add Remote telepresence to control any robot from your phone or PC
Add your robot to Exosphere
Sythiam Swag
Robot Sticker
People know your robot is capable when they see it is powered by Synthiam. These stickers are heavy duty for both indoor...
Recent Robot Skills
Exosphere
Remote telepresence and control for any robot - human-assisted autonomy, live audio/video, task marketplace to...
Autonomous AI
Autonomous AI for Synthiam ARC: conversational self-programming that interprets commands, generates code, and...
Picture In Picture
Picture-in-picture camera overlay: superimpose one camera onto another; configure source/destination,...
Featured
Real-time 3D servo visualization with motion trails, interactive camera controls and clear trail for ARC debugging and analysis.
Featured
Hex coaxial drone with 12 props and 15 lb thrust, 3D-printed frame to lift a WiFi antenna and camera for extended robot range via beacon tracking
question
Servo Control Voltage
I don't have a scope to verify this but would I be correct in assuming that the servo control voltage going to the servo is 3.3 volts on any particular digital port that a servo is connected to on an EZ Controller? The power to the servo would be the battery voltage that the EZ Controller is powered up from which is typically 7.2 Volts? Thanks...
1
2 k
DJ Sures |
blog
Canadian Prime Minister Gets Schooled With EZ-Robot
PM Trudeau experiences an EZ-Robot from Science North as federal grants bring EZ-Robots into classrooms across...
0
999
Miscellaneous
Iotiny
IoTiny small robot controller from EZ-Robot - a non-3D-printable placeholder for demonstrating robot construction and integration.
0
5 k
DJ Sures |
Sensors & Cameras
Developer Kit Camera
Developer kit camera demonstrating installation location and placement reference; not a 3D-printable part.
0
5 k
DJ Sures |
Miscellaneous
6 X AA Battery Holder
6 x AA Battery Holder by EZ-Robot, non-3D-printable battery holder for powering EZ-Robot devices
0
5 k
DJ Sures |
Servos
Continuous Servo With Wheel
EZ-Robot continuous rotation servo with developer kit wheel attached; placeholder item, not 3D printable.
0
5 k
DJ Sures |
question
Broken / Stripped Servo Joints
I am having problems with the plastic joints stripping out where the servo gear contacts the joint. I have not used this bot but 4 times and he is setup properly. where can I get replacement joints....neck.....leg off of foot. Does anyone have 3d printer files that I can use to print replacements?
2
2 k
teched |
question
Red Pepper Harvesting Robot
Hello friends , I will make an red pepper harvesting robot for my graduation project. It is my homework to graduate . The robot should be able to pick red vegetables from a garden and leave the green or yellow ones. It should perform this task autonomously and without damaging the plant. The Robot will go in a garden , When it detects rep pepper ,...
1
2 k
DJ Sures |
question
Logitech Joystick
I am looking into getting a logitech joystick, but I have a question. Does the Logitech joystick connect directly to the V4 EZB or does it require a computer? I just want to make sure it can be stand alone before I purchase the joystick...
3
2 k
thetechguru |
robot
Nomad's Meccanoid Max Gets Overhauld By Ez Robot
Customize a Meccanoid Max with an EZ-Robot costume, explore its drive base and gripper mods in a short demo video.
13
5 k
Nomad 6R |
question
Two 7.4 Volt 360 Servo Step Up To 48 Volt 1000 Watt Motors
Looking for recommendations on commercial fabrication of h-bridge for above. Burned up one electrical engineer (not literally) who tried to hook up ezb4 with 48v motor. Looking for someone who is honorable and wants a good day's work for a good days pay. Telemetry 100% complete, body 90% complete, mechanics 90% complete. Perferr performance...
3
2 k
Mastersailor |
question
Ez-B And Arduino Shield
After upgrading and swapping to the newer EZ-B board, it would be a shame not to use it with another robot. any consideration to building an Arduino Shield to accommodate the EZ-B? It would be overkill to add an EZ-B to an Arduino, but the potential would open up a wider market and audience. Perhaps the addition of an Arduino Library as well?...
3
2 k
ptp |