Hi guys, this is the first introducing part of a series, describing an autonomously operating hexapod with about 1 m width (my large insect). Idea behind this project: From early childhood on I wanted to build a kind of mechanical turtle or similar, being able to survive in the garden from spring to fall and doing whatever it would be programmed for, recharging its battery, seeking for shelter in case of rain, etc. Decades later (meanwhile a retired physicist, phd after 30+ yrs. in the space business) it was really time to realise this dream, meanwhile based on modern state-of-the-art electronics and software. Then, a colleague suggested to acquire an EZ-B V4-2 as the core element for such an undertaking and from thereon things picked up speed quite rapidly. As mentioned above, goal is the realisation of a quite large autonomous hexapod. The figure below is illustrating the general shape of this robot as well as the nomenclature for the legs (1, 2, , 6) and the servos (1.1, 1.2, , 6.3), respectively.
The base plate is made from 10 mm plywood and the legs from 20 mm x 20 mm pine wood. servo base blocks: 20 mm pine wood. A further light weighted plate (2nd floor) will be added later for accommodation of a scanning lidar, etc.. The hexapod’s legs are moved by 18 servos (Longrunner B07K68MK3Y:
In order to suppress unwanted rapid servo motions during EZ-B initialising, a switchable power distributor was added for each side (servos 1.1 through 3.3 and servos 4.1 through 6.3, respectively). These units are served by a central 2S2P LiPo battery (10.000 mAh) and are protected by individual fuses and are galvanically connected to the EZ-B.
Only the signal pin of each servo is directly connected to the EZ-B. servo Vcc and GND are both fed by these power distributors. Result: During EZ-B initialisation all servos are switched off - to be activated via toggle switches as required. Of course, all servos need to be positioned adequately beforehand. Currently, the hexapod is looking like this (together with his silent friend).
Programming was done in Synthiam BLOCKLY; surprisingly, the final version was completed within two days only !
Upcoming activities: First steps in the garden (Forward direction). Then: Backward, Turns, Sideways.
So long, that’s it for today,
Cheers
Volker
Other robots from Synthiam community
Joseph4760's Wall-E To Wall-E-Nator
Thecrustychicken's Crustybot 1.2
I dont have that problem. Must be that laptop of yours... Try other resolutions perhaps?
Have no problems with all my other desktops or laptops; it' s most probably related to this particular machine ...
... will dig deeper over the WE.
Now that is the strangest behavior I’ve seen. I cannot think of how that can even happen. There’s nothing different about those buttons and layout than any other buttons in arc.
It is a good idea to use a recent version of the ARC software. Difficult to diagnose with an older version.
make sure the tablet has the latest windows updates as well.
I use ARC 2021-02-02-00.
The Toughbook has a WIN 10 Pro version from summer 2020 (younger than all my other PCs).
But I will check for its WIN updates.
Same result upon installation of WIN updates.
Must be the machine itself.
No tragic, since these buttons can be brought to life via tipping the pen.
Hi guys,
here the latest and final images for the large hexapod (formally the "large insect"):
AND at least virtually ...
... it made it to Mars
!
Background: JPL NASADue to other projects that need to be finished within March, further field testing of the hexapod's autonomous outdoor navigation, etc. have been shifted to early April.
Cheers
Volker
Hi DJ,
the hexapod is currently equipped with 2 (two) EZ-B.
How should the second one be connected to the PC ?
As client as the first one ?
The EZ-B manual is not covering operation of more than one unit.
I think you want this: https://synthiam.com/Support/Install/Multiple%20EZ-B%20over%20WiFi