Robot Building Questions
Drive Real Robots, Anywhere
Remotely operate robots around the world or add live telepresence to your own build — straight from your browser.
Discover Exosphere
Robot Sticker
Feetech Serial Bus S…
Control Feetech SC serial bus smart servos via EZB UART or PC COM port with ARC virtual ports,...
Feetech RS485 Servo
Control Feetech serial bus smart servos via EZB UART or PC COM port in ARC using virtual ports...
Total Speech Recogni…
Offline Windows speech recognition with open dictionary, confidence filtering, and scriptable phrase...
Custom Movement V2 panel for ARC: scripts for F/R/L, Reverse, roll left/right, up/down with speed mapping to PWM for drones, mecanum & custom drives
Refurbish Hearoid with EZ-B: autonomous 24/7 self-charging robot with pan/tilt camera, image tracking, servos, ultrasonic sensor, lights and audio
Glickclick!!! Where Are You! Quatar, I Know, I Know....
yo! long time no talk....lets see for progress...i was able to do the body titlt...i will post a video tonight...(california time) thanks for your help man. i hope all is well and i hope to see some updates from ya soon. Carlos
0
2 k
Omnibot 2000 , Can I Use The Bv Hbridge Dj Sent?
Hey guys I'm pondering options here. Basically I just recieved the bv hbridge from dj and it says that its good for 1.5...
2
3 k
Robot Eyes
check this link out... I stumbled across their ebay store today and i'm impressed with their products. Some real neat stuff!...
9
4 k
Motor Load Detection
Hey DJ, At this stream at about 13:15 you said you had the motors plugged into the ADC port for load detection, How exactly did you do it? I would like to know for my omnibot
12
4 k
Question About Alternate Powered Servos
I have several servos tied into an alternate power source with the signal wire coming from the EZ-B. Question: When those servos are tied into the alternate power do they draw any current when the signal wire is not energized (ie. the EZ-B is turned off)? I want to know if I need to put an on/off switch in line with the power to those servos?...
2
2 k
Dj About The Ez Board
what crystal does it use and caps
0
2 k
Connection Problems
Hi Everyone, Maybe someone can help me out. I am unable to connect to the EZ board. There are no com ports listed under the "Connection To EZ-B" window. I tried to locate the board under my bluetooth settings as well however it was not discovered. I finally have a little free time so I am looking forward to getting this up and running....
6
2 k
Ez-Board - Some Questions
At last I have received my Complete Robot Kit! Once again big thanks to you! I have some questions about my EZ-Board: 1. What appointment of 6-pin connector on EZ-Board? It is designated as: (-MCLR * 3.3 * 5V * Gnd * Gnd * Vin) 2. On my EZ-Board V3, Rev1 there is no R1 and C1. The diode D1 is soldered differently. It is updating? 3. If the resistor...
3
2 k
Ideal Mounting Height ? , Ultrasonic Sensor / Radar
I am thinking of mounting the radar inside the base facing out. That's 8 to 9 inches I'm guessing after the wheels are...
1
3 k
Charging Base / How Can Robot Find Charger With Camera Or Map
Ok this is dedicated to making.a charging base for.omnibot 2000. Basically I would like ideas of...
14
5 k
Extend Servo Shaft
Waiting for my parts i'm searching a way to extend a servo shaft. Need this to fixed the robot arm to the servo who's intern the bot someone a idea ??
5
4 k
Quadracopters Perform James Bond
James Bond theme
3
3 k