All Community Content
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
Autonomous AI
Autonomous AI robot skill for ARC: vision-based LLM control, speech, movement, animations, memory,...
PWM Servo Ramping
Smoothly ramps PWM servos on EZB D0-D23 via Vx-to-Dx mapping for natural, gradual motion without...
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Featured
Map Myo armband gestures and accelerometer to servos and ARC scripts for arm-mimic control; supports multiple armbands.
Featured
Build and program a lightweight EZ-B3 quadruped with EZ-Builder; tips on 7.4V 800mAh LiPo hookup, servos, batteries and gait tuning.
question
Which Digital Pin In Vcc
Hello, I am sure a simple question, but I can't seem to find the answer. The EZB-4 info states: "Each port has 3 pins, which are Gnd, VCC and Signal. The Gnd and VCC are for powering the device connected to the port. The Signal pin is connected to the EZ-B Microchip for reading or writing data from Digital or ADC. The Gnd and VCC pins are not...
13
5 k
Dave Schulpius |
question
ARC Designing
probably a simple thing but how do you turn image of servos around to fit bodies in the design window
2
3 k
bborastero |
question
Humanoid Head Or Board Question
Hi I need help my recent order needs replacement parts what is the process to get this done.
15
3 k
Dunning-Kruger |
question
Rgb Unit On Humanoid Head
Are the i2c ports on the board auto sensing or is each one of the 3 a specific address? I found what looks to be the address range 0xA0, but I've also found V0 virtual...
24
5 k
cheko |
question
Roomba Wifi Kickstarter
Looks like a neat idea, the WiFi unit is small. The iOS and Android app looks interesting. The EZB(4) can do a lot more using a UART port and some two way conversation with the Roomba 500 through 800 models Roomba WiFi
2
3 k
Robot Doc |
question
Jd Webserver
Can I set the IP address of the webserver in my JD? My wireless network is 192.168.12.1, and I'd like my JD to be on that subnet. Thanks
8
3 k
DJ Sures |
question
Robot None Operational After Been Fully Charged
Hi I went through all the tutorials, calibrating the robot and was fully functional then the battery died. I put the robot on charge as per the tutorial guide and waited for the green light to clear. When i came to turning the Robot back on? Nothing? Could anyone advise? Thanks Kris
3
2 k
DJ Sures |
robot
Samac4750's I Bought A Head From Robotics
Animate a Robotics Squared head and articulated neck assembly.
0
805
samac4750 |
question
Bit Builder Link Wrong In ARC
I was going to look at the Bit Builder, under Project in ARC and the link to the " - STL Design Files and specifications for EZ-Clip, EZ-Robot Servos, EZ-B and other parts" is wrong as the hard coded link is: https://localhost:80/Community/Revolution/DesignFiles.aspx The external link I believe would be:...
0
3 k
JustinRatliff |
question
Servo Speed - Only Fast, Medium And Dead Slow Available
Hi gang, I have no problem getting servos to change speed using the ServoSpeed command in scripts and if I...
23
8 k
Dunning-Kruger |
question
Control Command In A Variable
Is it possible to insert a "control command" in a $variable? ex: $Female= ControlCommand("Speech Settings", SetVoiceGender, "Female") for now the result faults with "Missing String Quotes or Invalid Expression:" any idea?
7
3 k
Aerius |
question
Power Connect Plug
Received the developer kit today. It is not usable as is. The power connector plug will not go into the receptacle on the fuse base. The pin to inside diameter of the adaptor seems to be the problem. The supplied adaptor ID measures 2.14 mm. A similar plug with a 2.46 mm I.D. will fit. So take your pick either the pin is wrong or the adaptor is...
6
2 k
tifriday |