Robot Building Questions
Synthiam Credit
Earn Credit
Contribute to the community and earn credit to lower the cost of Synthiam robotics products and subscriptions.
Recent Robot Skills
NMS Navigation Data …
Query NMS lidar scan data by angle, with control commands for range, arc extremes, and obstacle...
Rplidar
Slamtec Lidar driver for ARC; scans 360° and publishes distance data to NMS for mapping, obstacle...
Kinect Xbox 360 Dept…
Converts Xbox 360 Kinect depth frames into NMS obstacle scans for ARC path planning, SLAM, and...
Featured
Send web-triggered IFTTT events from ARC/EZ-B: configure Maker Webhooks key and trigger applets to control SmartThings, WeMo and other services.
Featured
CARL on JD humanoid uses Synthiam ARC to see, learn, feel and act-face/object recognition, emotional speech, bio-inspired emotions.
question
Custom Charging Application Issue
Hello all, May i introduce myself, i am Garrett and am constructing a robot for a class project. I have run into an issue in charging my robot and have...
34
4 k
robotmaker |
question
Ebay Wall-E Prices
So, is DJ's hack of Wall-E the reason that the U Command Wall-Es have skyrocketed in price on e-bay recently? Are we, DJ wantabes, just bidding against each other? But seriously, I think the prices have gone so high lately that scratch building Wall-Es body is within reason. My only concern is how to build his tracks. Does anyone have any good...
7
3 k
LJ |
question
Wall-E Ends In Less Than 2Hrs......Let Me Have It
currently highest bidder....help me out guys.... please!!!!
10
3 k
LJ |
question
Glickclick!!! Where Are You! Quatar, I Know, I Know....
yo! long time no talk....lets see for progress...i was able to do the body titlt...i will post a video tonight...(california time) thanks for your help man. i hope all is well and i hope to see some updates from ya soon. Carlos
0
2 k
hoolagen1 |
question
Omnibot 2000 , Can I Use The Bv Hbridge Dj Sent?
Hey guys I'm pondering options here. Basically I just recieved the bv hbridge from dj and it says that its good for 1.5...
2
3 k
bret.tallent |
question
Robot Eyes
check this link out... I stumbled across their ebay store today and i'm impressed with their products. Some real neat stuff!...
9
4 k
hmanso |
question
Motor Load Detection
Hey DJ, At this stream at about 13:15 you said you had the motors plugged into the ADC port for load detection, How exactly did you do it? I would like to know for my omnibot
12
4 k
winstn60 |
question
Question About Alternate Powered Servos
I have several servos tied into an alternate power source with the signal wire coming from the EZ-B. Question: When those servos are tied into the alternate power do they draw any current when the signal wire is not energized (ie. the EZ-B is turned off)? I want to know if I need to put an on/off switch in line with the power to those servos?...
2
2 k
bret.tallent |
question
Dj About The Ez Board
what crystal does it use and caps
0
2 k
robotmaker |
question
Connection Problems
Hi Everyone, Maybe someone can help me out. I am unable to connect to the EZ board. There are no com ports listed under the "Connection To EZ-B" window. I tried to locate the board under my bluetooth settings as well however it was not discovered. I finally have a little free time so I am looking forward to getting this up and running....
6
2 k
cheekid |
question
Ez-Board - Some Questions
At last I have received my Complete Robot Kit! Once again big thanks to you! I have some questions about my EZ-Board: 1. What appointment of 6-pin connector on EZ-Board? It is designated as: (-MCLR * 3.3 * 5V * Gnd * Gnd * Vin) 2. On my EZ-Board V3, Rev1 there is no R1 and C1. The diode D1 is soldered differently. It is updating? 3. If the resistor...
3
2 k
Niek |
question
Ideal Mounting Height ? , Ultrasonic Sensor / Radar
I am thinking of mounting the radar inside the base facing out. That's 8 to 9 inches I'm guessing after the wheels are...
1
3 k
ww321q |