Robot Building Questions
Experience the transformation – subscribe to Synthiam ARC Pro and watch your robot evolve into a marvel of innovation and intelligence.
Synthiam Credit
Your Synthiam Credit is $0.00
Discover ways you can lower the cost of Synthiam products by contributing to the platform and community.
Earn Synthiam Credit
Exosphere
Loading...
Add Remote telepresence to control any robot from your phone or PC
Add your robot to Exosphere
Sythiam Swag
"I build robots" Hoodie
This heavy hooded sweatshirt is perfect for robot builders. The material mix of cotton and polyester provides warmth...
Recent Robot Skills
Voice Activity Detec…
Real-time voice activity detection (300-3400 Hz FFT) that triggers custom scripts on speech start/end, with...
ZAMA Emotion Model
Valence-arousal emotion engine generating persistent, configurable robot moods and event-driven emotional...
Feetech RS485 Servo
Control Feetech serial-bus smart servos via EZB UART or PC COM port; map ARC virtual ports to servo IDs with...
Featured
EZB UART parser and Serial-TCP bridge to connect EZ-Robot cameras via Teensy USB, enabling ARC camera control and USB-to-serial bridging.
Featured
Open-source R2D2 build: Arduino sensor controller with ultrasonic foot sensors, Razor/Saber Tooth motors, PS4/EZB control modes, rule engine
question
Jd Webserver
Can I set the IP address of the webserver in my JD? My wireless network is 192.168.12.1, and I'd like my JD to be on that subnet. Thanks
8
3 k
DJ Sures |
question
Robot None Operational After Been Fully Charged
Hi I went through all the tutorials, calibrating the robot and was fully functional then the battery died. I put the robot on charge as per the tutorial guide and waited for the green light to clear. When i came to turning the Robot back on? Nothing? Could anyone advise? Thanks Kris
3
2 k
DJ Sures |
question
Bit Builder Link Wrong In ARC
I was going to look at the Bit Builder, under Project in ARC and the link to the " - STL Design Files and specifications for EZ-Clip, EZ-Robot Servos, EZ-B and other parts" is wrong as the hard coded link is: https://localhost:80/Community/Revolution/DesignFiles.aspx The external link I believe would be:...
0
3 k
JustinRatliff |
question
Servo Speed - Only Fast, Medium And Dead Slow Available
Hi gang, I have no problem getting servos to change speed using the ServoSpeed command in scripts and if I...
23
7 k
Dunning-Kruger |
question
Control Command In A Variable
Is it possible to insert a "control command" in a $variable? ex: $Female= ControlCommand("Speech Settings", SetVoiceGender, "Female") for now the result faults with "Missing String Quotes or Invalid Expression:" any idea?
7
3 k
Aerius |
question
Power Connect Plug
Received the developer kit today. It is not usable as is. The power connector plug will not go into the receptacle on the fuse base. The pin to inside diameter of the adaptor seems to be the problem. The supplied adaptor ID measures 2.14 mm. A similar plug with a 2.46 mm I.D. will fit. So take your pick either the pin is wrong or the adaptor is...
6
2 k
tifriday |
question
Bad Servo?
Servo was working fine. Shutdown JD. Then when restarted JD found a bad servo? See pictures: See red area: J stress stress stress stress
3
3 k
Nomad 6R |
question
Finger Tip Sensors For Inmoov Hand
@Richard R. Are you going to use the finger tip sensora on your inmoov? I'm printing a new hand and would like to make use of the sensors but I don't...
10
6 k
Dave Schulpius |
question
Additional ARC Requests
Hi. I have a couple of ideas for the EZ-Robot team to consider that I think would be a nice addition to ARC. 1. When adjusting the volume slider from 100 on an EZ-B soundboard, say to about 60 for example, when a project is saved, closed, and reopened the volume goes back to the default 100. Would it be possable to add the ability to save the the...
11
4 k
Steve G |
question
Can I Change The Default Directory That ARC Defaults To?
I'd like to use a different default directory for saving my files and getting the examples. Is there...
5
2 k
Wolfie |
question
Additional Batteries For Jr
Why not put batteries in the feet of JR to extend his running time? A little mod to the feet profile and could put 1300maH in each foot. Or maybe extend the other part of the body to put in 2 other 1300's Just some thoughts
3
2 k
Morbeious |
question
Autoposition - Dc Motors & Servos
I have to admit I have not tried the AutoPosition control. It's still a bit of a mystery to me but I plan on diving into it in a few days. I've been focused on building a 7 pound arm with 4 joints for my B9 Lost in Space robot. I've now got it working smoothly; twisting and turning and lifting the weight. The first "elbow joint" lifts all...
8
3 k
Dave Schulpius |