Robot Building Questions
Unlock the true power of automation and robotics by becoming a proud subscriber of Synthiam ARC Pro.
Synthiam Credit
Your Synthiam Credit is $0.00
Discover ways you can lower the cost of Synthiam products by contributing to the platform and community.
Earn Synthiam Credit
Exosphere
Loading...
Add remote telepresence capabilities to your robot from your phone or PC
Add your robot to Exosphere
Sythiam Swag
Robot Builder Coffee Mug, 11oz
Start your robot building day on the right wheel, err foot, with this Synthiam Robot Builder black coffee mug. This...
Featured
Joystick (XInput)
Joystick control for XInput devices (xbox controllers, etc).
Featured
Optimus Prime
NEW UPDATES Scroll to the bottom to see the newest post* I just wanted to share some of the progress Ive got done on my newest EZ-B...
question
@Dj-What Is The Link For The O-Scope You Use?
I want to get an O-Scope to use for troubleshooting. I seem to remember you have a small o-scope that you like to use to look at servo signals but I cant find the forum discussion where you gave the link.
1
2 k
Jeremie |
question
Set On/Off On Ssc-32
How can I set the virtual ports on the SSC-32 to on or off? Doing Set(V0,On) doesnt do it which I dont get as you can control a servo using Servo(V0,90), or, like servo speed, is this not supported either?
8
3 k
Steve G |
question
Trouble Connecting 2 Ezbs
Im trying to connect two v4s in one project, but no dice. I know someone had this trouble before, but cant find the thread. They are both set to client mode, and the both...
29
6 k
Steve G |
question
Automating A Rc Car
I have a RC rock crawler that I would like to automate and turn into a Robot . If I but the EZ-B v4 Developer Kit will I be able to replace my receiver on my car with the Ezb-v4 unit and hook up my steering and ESC servos to run and stear the car through the programming to the . The car has 7.2 v Battery system on board which come through the ESC....
7
3 k
DJ Sures |
question
Ssc-32 Speed Control
Im currently installing and testing my new SSC-32 and testing servos using Servo(V0,xx) script commands which work great, and Im trying to get a connection init script sorted to set virtual servo speeds on start up, but cant figure out how to control speed. A take it that the ServoSpeed() commands are not supported for virtual servos as it doesnt...
9
3 k
Steve G |
question
Ezb V4 Short Circuit
I have a problem with my EZB. Its connected to a JD-head. That means 2 servos, rgb Eyes and camera. Powered with a 2cell lipo with a 2 Amp fuse inline. I had the EZB powered up and programming, shut it down to eat dinner. When I got back i plugged it in again but it didnt boot, 10 seconds later the 2 amp fuse was blown. I unplugged everyting from...
2
2 k
James Graham H… |
question
Longer Programming Time
i made a video how you can use an extended batt 2200 or 5000MaH with 12 servos .you will only see the female jack. tell me what you think plzz. 5000mah 2200mah
5
3 k
Nomad 6R |
question
Connection Question With More Then 1 Ezb4 Controller
Hello, i have 3 EZB4 Controller. I try to connect all Controller as Clients in my network. If i connect 1x EZB4 192.168.178.21 everything works. If i connect 2x EZB4 192.168.178.21 + 22 i get only the web interface from the first one 21. I also find only one the 21 in the EZB Software - not more! The same with 3x EZB4 To my Router: I check this...
15
4 k
Steve G |
question
Direct All Asounds To Pc Soundboard
Hi I robot is a little out of order right now and cant talk. Is it possible to send all talk and sounds to the PC soundbord instead. Right now I cant hear the battery warning for example. Best regards Niclas
7
2 k
eNiW71 |
question
Talking Servo / Inmoov Mouth Closed After Sentence
Hello, i have a problem with my inmoov. I add a talking servo i adjust the servo - everything is fine i have only one...
47
9 k
rentaprinta |
question
Dimensions For 8X8 Rgb Array
A quick question for DJ or Jeremie. Can I ask what the exact dimensions for the upcoming 8x8 RGB LED arrays are please (actual display and overall unit size)? I...
14
4 k
Steve G |
question
V3 To Monitor Two V4s?
Hi Folks, Hope everyone has been having a blast building robots! I havent posted since last year and now its time to scramble and get the G-Bot ready for this Halloween. Always a fun time! This year the G-Bot is getting upgraded from v3 to v4. I am excited to enjoy the better range and connectivity of wifi over Bluetooth. I’m also upgrading his...
4
2 k
Dave Schulpius |