antguru
Country: USA
Member Since:
Achievements
-
2011-12-25 - joined Synthiam
-
2011-12-25 - created first new question
-
2012-01-29 - joined your first forum discussion
-
2014-08-16 - connected ARC to the cloud
-
2014-09-20 - shared your first photo in the forum
-
2014-11-03 - attempted to help a fellow robot builder
Latest submissions
Questions (17)
Robots (1)
Skills (0)
General (0)
Hack Events (0)
Tutorials (0)
Apps (0)
Firmwares (0)
3D Parts (0)
Feature Requests (0)
question
Need Large Hexapod Leg / Servo Designs
How do I build a large hexapod leg / servo without breaking the bank? I want each leg to be about 2 feet long.
11
4 k
twa |
question
Digital Wait Usage Question
if I issue a script command such as: digital wait (d23, true, 50) what does the script execution do while it is waiting for the d23 status to change? can I start another script in parallel to process at the same time when we are waiting for the digital port to change? how would one start a parallel script? is there a tutorial on coding parallel...
3
2 k
antguru |
question
Need Sugestions On How To Control A Moded Servo With Ezb For Linear Use
here is a thought that needs some pruning. I need a linear actuator that has...
12
4 k
antguru |
question
Sixc Does Not Make Sound
Six arrived yesterday. Thanks However the robot will connect to my WiFi in AP mood but it does not make any sound when booting up. Whats wrong?
15
4 k
DJ Sures |
question
Wanted A Full Datasheet For The New Ez-Robot Motor Control
can anybody post a full datasheet for the new motor control. I am wondering what the maximum voltage...
8
3 k
jstarne1 |
question
Dinsmore 1525Nd Hall Efect Compass Sensor
I wanted to share my new find with others. at a local hamfest I purchased two Dinsmore 1525ND nd for no damping on outputs electronic hall effect sensors for $5. these sensors have both sine and cosine outputs. I have attached a data sheet for reference. So far the results are pretty good, now to interface it to EZ v4 instead of my development...
0
2 k
antguru |
question
How To Properly Use The Project Configure Function
I have been trying to figure out how to use the project configure control. I need some help please. 1 what does load do in configure. doesnt the calibration get saved when I save a project 2 I need to calibrate each end of the servo travel or just the middle or 90 position displayed? 3 how do I save each end and middle cal points? 4 what name if...
8
2 k
VGosine |
question
First Impressions Of Six
I received Six two days ago after having it on order for one year. I was glad to see it. It took my wife and I four hours to assemble Six. The assembly instructions were...
12
4 k
Nomad 6R |
question
Need Example On How To Program Six With Additional Lever Servos As Sold Oin Ezbo
the software example for six that will run each of the six...
7
3 k
Dunning-Kruger |
question
Submarine / Rov Robot Ideas?
Has anyone built a sub / ROV and wants to share the design?
4
3 k
Antron007 |
question
Ezb Firmware Update Failure Help
ok all was working fine with ARC until i decided to upgrade to 12 26 version. down loaded ok then tried to run firmware update program. failure program...
26
4 k
mitchmen14 |
question
Auto Startup
How does one create a script to self start the robot program? It must load the file, connect to the comm port in use, and then start the program. It should have a time delay upon startup to allow someone to abort the auto startup. What do you think DJ?
10
3 k
robotmaker |
question
New Rov Submarine Bluetooth Questions
Well a friend asked if we could eliminate his thick control cable running from his boat to his ROV submarine by using EZ-B. My first thought was all but the two power wires. However this will require that the bluetooth link and camera links be coupled over the 12 volt DC power wires about a 100 feet in water. Any body have any ideas on how to do...
11
3 k
robotmaker |
question
ARC Soundboard Problem
I tried to get the soundboard control working in the latest version of software. No luck. First it looks diferent then what the tutorial shows. Second it is missing the text on the spaces normally used to label the buttons in the control. I want to simply play a .wav or .mp3 sound effect on my pc that is running EZB. Windows 7 operating system. Can...
3
2 k
DJ Sures |
question
Printing Documentation ?
How do I downl0ad the entire set of controls and scripting documentation for bedtie reading?
0
2 k
antguru |
question
General Questions
Santa just gave me my EZ-B Neat tin can for a bot. The mem stick did nt show up under computer in windows 7. Any thoughts?
2
2 k
Choyster |
question
General Questions
Santa just gave me my EZ-B Neat tin can for a bot. The mem stick did nt show up under computer in windows 7. Any thoughts?
0
2 k
antguru |
No general conversations. Click here to start a conversation.
No robot skills. Click here to view the Robot Skill Store.
No live robot hacking sessions. Click here to view the past live robot hacks.
No user tutorials. Click here to view all user tutorials.
No robot apps. Click here to view all user robot apps.
No firmwares. Click here to view robot hardware and firmwares.
No 3D printable parts. Click here to view 3D printing robot library.
No features requests.