cE9s4PsOgeBQIORwjd5!~~60_1-634818020230156250.jpg)
BO)Lupuc4g~~60_35-634706297915000000.jpg)
LupbT6!~~60_35-634706298769375000.jpg)
C5j!~~60_35-634655044863125000.jpg)
C5j!~~60_35-634659603510781250.jpg)
C5j!~~60_35-634651704046230469.jpg)
This project has evolved some , the basic rundown is I'm modding two Omnibots , one a regular the other a larger 2000 model. I will have two ezb kits , rad base idea was thrown out because of so much noise but could go back on the table if the omnibot drivetrain is too weak to pull it.
By jstarne1
— Last update
Other robots from Synthiam community
Mastersailor's Noisy Boi (Trademark Pending)
Sub 10 foot remote network robot Speed 47 mph Plow Flamethrower Remote start 1000s of devices Security, email push Has...
Kullthulu's Artemis - The Household Service Bot
Hello Everyone! I posted a project a while back, (2014 so a wayyyyy while back) about a robot I was building that at the...
Andy's Antonn
Antonn started off as Lilian. She had the ability to move through the family room, react using voice commands, speak,...
If you do then you will lose the lights in the eyes. I dont have a OMNI head to reference but if there is space after mounting the guns through the parabolic lens you could drill and mount 3 evenly spaced LEDs around the lens. Then have them flash when firing.
Ok EZ roboters , I ran by Wal-Mart's clearance isle and bought 2 HP speakers with built in amp and flexible tubing I believe will fit the diameter of the vacuum components. Take in mind guys I'm no engineer or have a degree in electronics , I'm just winging it.
Also in the clearence isle , laser pointers! , $1.75 , I bought one to test and may grab another couple to do the predator tri laserHow about these TTL controlled from Sparkfun?
Link
hope very soon to see it painted
Body stretch update! ok as everyone saw I posted I'm stretching Jarvis height in two places. I picked up sheets of plastic 1/8" thick and PVC square tubing, I plan on this being a modular section which can be removed at any time. The structure will be 1/4" ply wood and possible 1" PVC pipe as support structure as Glickclick suggested. Then the outside surface will be plastic , like a veneer it will only be the visible surface but not load bearing. I could have just smeared body filler or fiberglass epoxy on wood and shaped it but using plastic to match the existing surface will save my fingers from hours of sanding and already be smooth.
. I will add pictures of the sheets after I take a shower. They were 4 dollars each PVC , very pricy but more than work not having to spend the weekend sanding and shaping is worth it to me. Soon as body stretch is done , servos cut out , vacuum also cut and any needed molding there I will be ready for paint! I have a busy weekend ahead of me! If anyone has suggestions on the airsoft gun operations or placement please shout out to me
good work ,thats better then using wood,i would use very light materials i do change plus plastic and pvc will work still at work we have a utrasonic welder use to combined plastics together or mend or weld,too big for my place,but i might can use it
We have a plastic welder to "finish" the seams . During.the fitting.process I will use PVC medium.thickness CA glue.
CA glue doesnt hold well on pvc tubes,this much glue that would work,i made a underwater ROV with a camera and had problems trying different glues and a pvc CA glue too,doesnt bond very well and with your design you need a very good bond, plastic welder the company has is a very very tall and big machine over 600lbs i would use fitting they sell at homedepot i think that cam mount to a base or plywood,pvc flange its called and then use pvc cement and twist putting pvc cement on outside of the tube wont work,need no air to make it work,not like CA glue