The easiest way to program the most powerful robots.
Use technologies by leading industry experts.
ARC is a free-to-use robot programming software that makes servo automation, computer vision, autonomous navigation, and artificial intelligence easy.
Get Started
I saw the arm on eBay and I tought its to big and no good quality but I was wrong.
Very cool Mix and nice work, hehe :-)
the arm comes in small pieces. is it difficult to build the arm ?
How good is the quality of servos and pieces?
regards
Marty
the arm is fully assembled,do need some adjustments fine tunning.
arm+hand
and here full robot
full robot
each side has a connection.
if they are strong,i dont know that .
the arm-servos work problem-free with the ez-robot controller ?
cheers
the arm is heavy for jd.
i think usefull for mecanoid robot.i have now set up robi eyes.later video.
now i test the mouth led.
Would like your help with not only the rgb eyes for my GF's Robi, but the mouth led also.
the rgb dont work on robi cause he dont have a rgb connector like the ezbv4.
i just notest i dont have the wire for the mouth led.just ordered one.
i use same colors as ptp explaned few weeks ago.also the angle robi head,
is diff then the jd head is flat.
thank you for the video.
Hmm Robi is going to be a challenge with programming thats for sure...getting rgb's to sync is a nightmare for me.
am using original eye boards from robi.
the rgb from ez is much easier to use.but you have to have diff eye glass,
and 3d print part to get all the light inside eye case.
Just remembered Smarty's robot, the one with the Robi head, i wonder how he managed to sync those rgb's?
robi's eyes are not rgb,they are tri color leds.
@Smarty,
could you please tell us how to make Robi's eyes work?
yourre correct ,amazing video.
Great video ive watched it many times even though i can't understand German.
I noticed there is only a 4hr time difference between Belgium and Australia, so we should skype sometime soon?
Im just waiting on servo extension cables and then im going to power up my humanoid for the first time, we should get our robots to have a Skype chat together some time?
hope he respond.you have a jd humanoid?
No i don't have a JD, my avatar is my humanoid.
Hey being in Belgium, does that mean you can understand German also?
yes cable.its a 4 pin cable.
here a pic if you use an ezb,its handy for data.
Will control him with my phone first.
Need to also find a 6v regulator for the neck servo, that's the only servo i haven't calibrated yet.
Better pic, last one was horrible.
Being a neck servo, i wonder if i could get away with putting 7.4v through it..its only rated for 6v and its very cheap so im sure it would go pop just by being plugged in?
i think that it will work.for your 6 volt servo's
i have to talk to you later.have to make myself reddy for chemo,
in a few houres.
seeya
Good luck for your chemo amigo.
here the solution for the robi eyes.read this topic.they work on 3 rgb ,
connectors and have thousand colors.you can use 3 rgb windows.
the adresses for each rgb connector are in the topic.
topic robi eyes
neon pixel bit
put a light between the speaker and sound-cable.. thats it.
but be carefull.. use a resistor.. so the LED is never to hot.
the eyes are selfmade :-)
I cannot talk about all my tricks, because I'm selling the robots and that's a hard job :-).
do you have a pic from led whit resistor?
ah i like the way you explained that, many thanks.
In regards to a resistor, doesn't the EZB4 have built in 3.3v resistors?
Smarty, your Kondo robot with the Robi head, his RGB eyes are really good, you have the colors working perfectly, thats what i would like to do with the small Robi i have here.
I 100% agree with you there, if your selling robots then i wouldn't give out any tricks of the trade either...sounds like a dream job.
i got 6 colors but not all are very bright.
The colors are bright enough i think.
Cool figure in the background.