Profile Picture

jeffmorris

Country: USA
Member Since:

Achievements

  • 2012-09-09 - joined Synthiam
  • 2012-09-09 - created first new question
  • 2012-09-26 - joined your first forum discussion
  • 2012-10-28 - posted a robot project showcase
  • 2016-01-20 - connected ARC to the cloud

Latest submissions

question
Servos Run In Wrong Directions?

Servos Run In Wrong Directions?

I'm 3D-printing the parts to build the humanoid robot. I followed the instructions on building the robot but my own servos with metal gears run in wrong...
question

I Need Short Spacer

I need to make a short spacer similar to the expansion block but just the top and bottom parts of the block. I tried to load the STL file into 3DS Max but I don't know how to remove the middle part, leaving the top and bottom parts, and merge the top and bottom parts, forming a short spacer to clear the Alternate Power Adapter that I put into the...
question

Need 3D Model Of Micro Servo With Metal Gears

I need 3D model of micro servo with metal gears like the ones that came with the humanoid robot. I want to 3D-print dummy micro servos. I don't have the real micro servos. Also, I have problems 3D-printing some robot parts that require supports. Removing the supports leave rough surfaces on robot parts. I don't have the correct filament for...
question

Parts For Revolution Jd Robot?

I am 3D-printing the parts for Revolution JD robot. I already have the HD servos but I don't have other parts like EZ-Robot Controller, camera, micro servos, LiPo battery and charger, RGB LED block, switch, fuse, and connector between torso and controller. I would buy the EZ-Robot Developer Kit but the kit doesn't have the parts that the robot...
question

Motor Driver Or Esc For Large R/C Car?

Please help me buy a motor driver or ESC for a large R/C car. The car is VW New Beetle made by New Bright. It is over two feet long. I may have to replace the motor for steering front wheels with servo. The motor driving rear wheels is about 1-1/2 inches long.
question

Two Ez-Robot S08nf Servos Are Bad

I found out that two EZ-Robot S08NF servos are bad. How can I have them replaced?
question

Confused Using Auto Position In ARC

I add "Auto Position" control to ARC project. I set up six servos in the control. I create three frames and one action. I am confused by "Fine Tune" dialog box. How do I use the "Fine Tune" dialog box"? Even after centering the servos before attaching them to the robot, the joints are slightly bent instead of straight.
question

First Time Here And A Few Questions

I got the EZ-Robot kit. Can the EZ-Robot board operate independently of the computer after programming it? Which motor driver should I buy for wheelchair motors? Are the servos from Vex Robotics Kit compatible with EZ-Robot? They either run too slow or don't run at all. What's the maximum voltage of the power supply that is plugged into the...
question
Suggestions For Accelerometers, Gyroscopes, And Gps Receivers?

Suggestions For Accelerometers, Gyroscopes, And Gps Receivers?

Suggestions for accelerometers, gyroscopes, and GPS receivers? I would like to build a model car...
question
How To Make Servo Brackets Like Those On Lynxmotion Robots?

How To Make Servo Brackets Like Those On Lynxmotion Robots?

How can I make servo brackets like those on LynxMotion Robots out of wood and plastic? I want to try...
No general conversations. Click here to start a conversation.
No robot skills. Click here to view the Robot Skill Store.
No live robot hacking sessions. Click here to view the past live robot hacks.
No user tutorials. Click here to view all user tutorials.
No robot apps. Click here to view all user robot apps.
No firmwares. Click here to view robot hardware and firmwares.
No 3D printable parts. Click here to view 3D printing robot library.
No features requests.