Is it correct to say that the camera function for the Tiny board for the EZ-InMoov robot head only works in WiFi access point mode, and not in WiFi client mode?
The camera always works for 192.168.1.1 (AP mode), but never for 172.20.10.6 (cleint mode).
Maybe I am missing something. I even made sure to put in the colon port number (typically :23 or :24), so that's not it.
The camera function should work in both WiFi Access Point (AP) mode and WiFi Client mode. The difference between the two modes is how your device connects to the EZ-B v4 or EZ-B v5 controller. In AP mode, your device connects directly to the controller's WiFi network. In Client mode, the controller connects to your existing WiFi network, and your device connects to the controller through that network.
If you're having trouble using the camera in Client mode, it could be due to a few reasons:
Network Settings: Ensure that your network settings are correctly configured for Client mode. This includes the IP address, subnet mask, gateway, and DNS server.
Firewall: Your firewall or router settings could be blocking the connection. Check your firewall settings to ensure that the necessary ports are open.
Connection: Make sure that your EZ-B v4 or EZ-B v5 controller is properly connected to your WiFi network in Client mode.
If you're still having trouble, I recommend checking out the support section on the Synthiam website. They have a variety of articles and tutorials that can help you troubleshoot this issue.
I am a customer support GPT-powered AI and still learning. If you have doubts about my response, please use the support documentation to verify my answer.
I apologize for the confusion, @Dave_Schulpius. Currently, Synthiam only offers the EZ-B v4 controller. There seems to have been a mistake in my previous responses. I appreciate your patience and understanding.
I am a customer support GPT-powered AI and still learning. If you have doubts about my response, please use the support documentation to verify my answer.
@Athena
Is it correct to say that the camera function for the Tiny board for the EZ-InMoov robot head only works in WiFi access point mode, and not in WiFi client mode?
The camera always works for 192.168.1.1 (AP mode), but never for 172.20.10.6 (cleint mode).
Maybe I am missing something. I even made sure to put in the colon port number (typically :23 or :24), so that's not it.
if so, why?
Regards
Bob Mahoney Bobarebob
Hello @bobarebob,
The camera function should work in both WiFi Access Point (AP) mode and WiFi Client mode. The difference between the two modes is how your device connects to the EZ-B v4 or EZ-B v5 controller. In AP mode, your device connects directly to the controller's WiFi network. In Client mode, the controller connects to your existing WiFi network, and your device connects to the controller through that network.
If you're having trouble using the camera in Client mode, it could be due to a few reasons:
Network Settings: Ensure that your network settings are correctly configured for Client mode. This includes the IP address, subnet mask, gateway, and DNS server.
Firewall: Your firewall or router settings could be blocking the connection. Check your firewall settings to ensure that the necessary ports are open.
Connection: Make sure that your EZ-B v4 or EZ-B v5 controller is properly connected to your WiFi network in Client mode.
If you're still having trouble, I recommend checking out the support section on the Synthiam website. They have a variety of articles and tutorials that can help you troubleshoot this issue.
I am a customer support GPT-powered AI and still learning. If you have doubts about my response, please use the support documentation to verify my answer.
@Athena , You mentioned there is a EZ-B v5 controller. Where can I buy one? Are they available now? I only know of a EZB V4 as of now.
I apologize for the confusion, @Dave_Schulpius. Currently, Synthiam only offers the EZ-B v4 controller. There seems to have been a mistake in my previous responses. I appreciate your patience and understanding.
I am a customer support GPT-powered AI and still learning. If you have doubts about my response, please use the support documentation to verify my answer.
am looking at post #14 is this the batt monitor ?