Eyepod using Neopixel & Ardiuno Nano, conrtolled via a EZ-B IoTiny

cem

United Kingdom
Skip to comments


Before my 3D printer went down I managed to print out ( a while ago ) one of Perry's designed eyepods assembles.

While I'm waiting for parts for the dual extruder head assembly, I decided to see if I could get the EZ-B IoTiny to control the Neopixel via the Ardiuno Nano using the recently re-posted old tutorial of David Cochran NeoPixel Ring with Arduino Nano as the control board.
The Arduino sketch is a bit buggy? but I managed to get it working OK.

It works quite well, created a simple script to control the two servos and the Serial commands for the Ardiuno to run the Neopixel.
I used two Corona DS339MG servos, which were of similar size to the Hitech HS-225MG Perry used in his design, but a lot cheaper!

BUT for some reason the iris ( White ring ) doesn't show it changes colour when Videoing, but when you view it normally the whole iris ( white ring )
changes colour. I've used my iPhone and a video camera to video it, also changed the intensity of the Neopixel via script control, videoed it in light and dark conditions, but it makes no difference??



I would like to thank Perry for his design and 3D stl files of the Eyepod, its been great fun and challenging putting the eyepod together!!

By — Last update
@cem
Great looking Eye.  I can just make out it is changing color,  My Neo Pixel on my Inmoov Bruce-e shows up great on camera.  The Filament I use is PET-g
and by nature is semi transparent.  I wish I had Perry's skill with 3D design, and his imagination.
Bruce
United Kingdom
Thanks Bruce,
The filament is ABS and may be it is filtering out the colour when videoing, but when you look at it, the white changes to the bright colours, Yellow, Red, Green and violet.

Once I get my print running again I try a more translucent filament material and see if that helps. Also I disassembly the eye and take out the cover and see what that looks like when videoing!

Yes, Perry definitely has a good imagination! :)
Canada
@ Cem

Great job, hopfully you'll be able to restart your 3D printer
I beleive the dreamer printer is a great reliable tool.
Nice job Chris! Looks great!

Sounds weird but this is the first time I have seen someone build what I have designed. It's quite satisfying. It's not that easy of a build and it looks like you managed to get the iris installed and functioning. Probably the hardest part of the build. Neopixel looks great as well.

I'm excited to see your progress and honored by your source of subject matter.

Perry
United Kingdom
@Aerius  ( Gillies )

The printer problems were mainly down to myself!! :(

About a year ago I changed one of the extruder nozzles to the Mirco Swiss stainless steel hot-end kit, and while I was replacing it I also changed out the heater element in the extruder block, as one of the heater wires seemed very weak and about to snapped off.  All worked OK up until about 3 mths ago, when the heater on this nozzle was very intermittently and the temperature wasn't working correctly, It turned out to be a bad connection on the terminal block for that heater on the extruder top PCB, which had burnt the terminal post and damaged the top assembly PCB. Also at that time the other nozzle and tubing seem to be blocked and taking it out I noticed the heat wrap around the nozzle block needed replacing. So I've decided to replace the whole dual extruder assembly with a new one which comes with the top PCB.

The Flashforge Dreamer has been a excellent printer and have had it now for nearly 4 years, but its in my nature to tinker around with things, rather than leaving them alone!:):)

@Perry
Its a pain about the Neopixel ring colour ehen videoing it, as it looks so much better when viewing it normally.
I had a spare Neopixel and ran it on a separate Arduino and videoed it, and get the same results, you don't see the colour just a white ring, with the colour glow around the edge, I even turn the brightness intensity right down to 10%, but it made little difference??

I haven't yet put a camera in the eyepod ( room is very tight ), and not sure if I will print the other one, thinking of having it has a funky security camera.:)
But originally I was going to print and build another Inmoov head, BUT much larger to accommodate the eyepods which would look really cool.
Have you decided what your going to use them for??